3M Multi-Touch C4267PW Скачать руководство пользователя | Manualshive

Страница: 42 / 45

background image

42

3M™ Multi-Touch Chassis Display User Guide

3M Touch Systems, Inc. Proprietary Information – TSD-45335

Issue

Solution

•

Check that the video input from the video card falls within the refresh
rate of the display. Refer to Supported Video Display Modes and
Refresh Rates in Chapter 1.

•

Check that your computer is using a supported display mode. Refer to
Supported Video Display Modes and Refresh Rates in Chapter 1.

No image displayed (blank
screen)

Is the display in Power Management mode?

•

If the LED on the rear of the display is flashing amber, touch the screen,
press any key on the keyboard, or move the mouse to restore operation.

•

Verify source selection is correct (OSD)

No image displayed (blank
screen)

Are the brightness and contrast settings too low?

•

Use the display controls to adjust these values.

Abnormal image

•

Check that the video input from the video card falls within the refresh
rate of the display. Refer to Supported Video Display Modes and
Refresh Rates in Chapter 1.

•

Check that the video cable is connected properly and securely to the
display and the computer.

Colors of image are
abnormal

•

Check that the video cable is connected properly and securely to the
display and the computer.

•

Check that no pins are bent in the video cable connector.

Disturbances on the screen

•

The video display adjustments are incorrect. Refer to Chapter 2 for
adjusting procedures.

Troubleshooting the Touch Sensor

If you are experiencing problems with the touch sensor, check the following list of
common installation errors.

Table 22. Common Touch Sensor Installation Issues

Common Installation
Issues

Possible Solutions

Touch sensor does not respond
to touch

•

Review the installation procedures. Are all cables connected properly?

•

After you installed Touch Software, did you restart your PC to activate
the touch sensor driver?

•

Remove the sensor communications cable and plug it back in.

•

Disconnect the power cable and plug it back in.

Touch sensor is not accurate

•

Calibrate the touch sensor for the current video resolution and
operating system. Refer to the Video Alignment section in Chapter 3
for additional information.

«
...
40
41
42
43
44
...
»

Содержание Multi-Touch C4267PW














































Отзывы:

Нет отзывов

Похожие инструкции для Multi-Touch C4267PW

Бренд: G-Lab Страницы: 25

e-Machines E17T4

Бренд: AOC Страницы: 72

Бренд: Wohler Страницы: 2

Бренд: Biolight Meditech Страницы: 25

Бренд: I-Tech Страницы: 50

Бренд: Gator Страницы: 12

Бренд: IAdea Страницы: 12

Бренд: Microlife Страницы: 32

Бренд: I-Tech Страницы: 20

ProLite T2234MSC

Бренд: Iiyama Страницы: 31

V-SENSE 8404 4K T10

Бренд: i3TOUCH Страницы: 53

Бренд: ROVARY Страницы: 38

Бренд: AOC Страницы: 33

Бренд: Vehicle Systems Страницы: 9

Бренд: Polar Electro Страницы: 25

JUMPFLEX 2857 Series

Бренд: WAGO Страницы: 2

Бренд: V7 Страницы: 13

Бренд: 4D systems Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды