3M Dynatel 2250M Скачать руководство пользователя страница 41

Страница: 41 / 65

78-8130-6150-0-F

D. Dual Marker Locate

1. Press

Locate/OK

[5].

2. Press

Marker

[SK].

3. Press

MARKR 1

[SK Toggle] to select desired

utility.

4. Press

MARKR 2

[SK Toggle] to select desired

utility.

Note: Only the marker types enabled in the setup menu will be shown. (See Enabling/

Disabling Marker types, Section 13A). When scanning for markers, the gain level [4]

should be set high.

− The third and fourth soft key commands will populate with the types of utilities

selected for Marker 1 and Marker 2.

5. Adjust the

Gain

[4] down until the bar graphs open.

− The bar graph will close, the audio will increase, and the Signal Strength [10]

will increase when the receiver detects a marker of the specified utility.

− When one of the two markers is detected, press the “XXX Only” [SK] for the

detected utility marker. ("XXX" represents the marker types selected. In the

above example, PWR Only and TEL Only.)

− The receiver will switch to Single Marker Locate in order to pinpoint the

marker.

6. Press

Markr 2

[SK Toggle] to return to Dual Marker Locate.

E. iD Marker Depth

1. Lower the tip of the receiver to the ground over the pinpointed marker.

2. Press

Depth

[SK].

− The receiver will examine the marker

(Calculating, please wait...)

− If the marker is a 3M

™

Dynatel

™

Marker, the receiver will display the depth

of the marker, and its identification serial

number.

Содержание Dynatel 2250M


































































Результаты поиска

Содержание Dynatel 2250M

Отзывы:

Похожие инструкции для Dynatel 2250M

Бренды по названию

Популярные бренды

3M Dynatel 2250M, Руководство оператора

Результаты поиска

Содержание Dynatel 2250M

Отзывы:

Похожие инструкции для Dynatel 2250M

Бренды по названию

Популярные бренды