3M Dynatel 2250M Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 65

background image

78-8130-6150-0-F

23

B. Dyna-Coupler Method

m

WARNING

This WARNING applies to the following 3M Dyna-Couplers;
• 3" (75 mm) - Part number 3001
• 4.5" (114 mm) - Part number 4001
• 6" (150 mm) - Part number 1196
• All accessory kits containing any of the listed Dyna-Couplers - Part numbers 3019, 4519,

1196/C

A potential for electrical shock exists when using the Dyna-Coupler on cables energized with

electrical power. Use appropriate safety procedures.
DO NOT USE ON CABLES CARRYING IN EXCESS OF 600 VOLTS RMS.

Use a ground extension cable,

or wire, and ground rod set-up

between a target pipe/cable and

a gas meter valve/box, or cable/

electrical meter box. This will

isolate the locate signal to the

target pipe/cable section below

the meter/box, between the

grounding points. This provides a

good return path for the tracing

signal. Insulating coupling above

a gas meter valve on a pipe will

isolate the returning signal from

ground and may make locating

more difficult.

1. Connect the Dyna-Coupler to the transmitter

Output Jack

[T-6] using the coupler

cable (9011).

2. Clamp the Dyna-Coupler around the cable or pipe, below any bonds, just before it

enters the earth.

The jaws of the coupler must fully close.

3. Press

Trace

[T-3] to turn on the transmitter. Press again to select 8 kHz, 33 kHz or

200 kHz.

Note: When using a Dyna-Coupler, always select high or maximum output power level

by pressing the Output Level [T-5] key on the transmitter.

«
...
21
22
23
24
25
...
»

Содержание Dynatel 2250M


































































Отзывы:

Нет отзывов

Похожие инструкции для Dynatel 2250M

Бренд: Panasonic Страницы: 9

Бренд: Parata Страницы: 40

Бренд: Panasonic Страницы: 30

Бренд: Califone Страницы: 7

Бренд: CALITEK Страницы: 16

Бренд: LAHTI PRO Страницы: 20

Бренд: LAHTI PRO Страницы: 16

Бренд: J&M Страницы: 53

Бренд: Qazqa Страницы: 2

Бренд: Gamry Instruments Страницы: 69

Бренд: Gamry Instruments Страницы: 30

Бренд: Gamry Instruments Страницы: 88

Бренд: Rayger Страницы: 2

Бренд: Maeda Страницы: 276

Бренд: natus Страницы: 20

Dantec Keypoint G4

Бренд: natus Страницы: 42

Бренд: natus Страницы: 149

Бренд: UNI-T Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды