3M Dynatel 2250M Скачать руководство пользователя

Страница: 11 / 65

78-8130-6150-0-F

NOTE: 12 Watt Output Level varies by frequency. Output is limited to 10 watts at

33 kHz and 1 watt at 200 kHz using the direct connection method.

[T-6] Output Jack:

Port for direct connect cables or Dyna-coupler.

[T-7]

External Jack:

Port to connect cigarette lighter adapter cable, or rechargeable

battery (2200RB). Input voltage level: 9-18 VDC. (Only on 5-watt and 12-watt

transmitters.)

F. 2273 Transmitter Keypad and Connector Definitions

T-1

T-2

T-3

T-4

T-5

T-7

[T-1] off:

Turns unit off and performs battery test.

[T-2] on: Ohm-meter / Fault Locate / Tone:

Turns the unit on and cycles through the

following commands when pressed repeatedly.

Ohm-meter:

Measures the continuity of the trace conductor/pipe and its far-end

ground. It is also used to measure the fault resistance to earth.

Fault Locate:

(2273M units only) In this mode, the transmitter sends two alternating

locating frequencies (577 Hz and 33 kHz) as well as fault signals 10 and 20 Hz.

Tone:

In the tone mode, the transmitter generates 577 Hz and 200 kHz signals.

[T-3] on: Trace (frequency):

Turns the unit on and places the unit in Trace mode.

Select Frequency:

Press Trace [T-3] repeatedly to cycle through the transmitter’s

active frequencies (577 Hz, 8 kHz, 33 kHz, and 200 kHz). The selected frequency

will be displayed [T-4]. ‘ALL' indicates that the following active frequencies are

transmitting simultaneously: 577 Hz, 8 kHz, 33 kHz and 200 kHz.

[T-4] Digital Display:

Indicator Flags:

These flags coincide with the operational mode of the transmitter.

(From top left to bottom right) Fault mode [T-2] (2273 units only), Tone mode [T-2],

Trace mode [T-3], Ohm-meter [T-2], Voltage (at start up the transmitter checks for

foreign voltage), and the Output Level Flag (no flag = normal output; flag = high

output; flashing flag = maximum output).

Digital Display:

Indicates frequency, relative current, resistance, battery level and

voltage (if present on target).

[T-5] Output Level:

Cycles output level; normal, high and maximum.

Normal=No Flag; High=Flag; Maximum=Flashing Flag (indicated in

Digital Display

[T-4])

NOTE: An external 12-volt power source is required to obtain Max Output level (12

watts for 12-watt transmitters and 5 watts for 5-watt transmitters).

Содержание Dynatel 2250M


































































Результаты поиска

Содержание Dynatel 2250M

Отзывы:

Похожие инструкции для Dynatel 2250M

Бренды по названию

Популярные бренды

3M Dynatel 2250M, Руководство оператора

Результаты поиска

Содержание Dynatel 2250M

Отзывы:

Похожие инструкции для Dynatel 2250M

Бренды по названию

Популярные бренды