3M Dynatel 2250M Скачать руководство пользователя страница 39

Страница: 39 / 65

78-8130-6150-0-F

10. After a fault is located and pinpointed, move the Earth Contact Frame about one

Earth Contact Frame width away from the fault and insert it in the ground with the

green-banded leg towards the fault. Compare the numeric signal level with the fault

level reference signal indicated in the lower left box labeled

Ref

. If the reading is

within 12 dB of the reference signal, the operator has found the major fault. If the

fault reading does not fall within 12 db of the reference signal reading, multiple

faults may exist. The signal level of this secondary fault can be saved by pressing

Fault 1

[SK] or

Fault 2

[SK]. The fault with the highest reading will be the primary

fault.

Note: For additional information about locating buried sheath faults and earth

return faults, please see the 3Mtm publication Cable and Pipe Locating Techniques at

www.3M.com/dynatel.

13. Locating 3M

™

Electronic Markers and

™

iD Markers

(3M

™

Dynatel

™

Models 2250M-iD and 2273M-iD only)

A. Enabling/Disabling Marker Types

Menu [6] + >>More [SK:4] + Setup [SK:6] + >>More [SK:6d] + Marker Type [SK:6f]

The unit will default with all markers enabled (

1. Press the up/down arrows [SK] to highlight a

utility to enable or disable.

2. Press

Enabl/Disabl

[SK].

− Only the markers that are enabled (✓) will

be available in the locate mode.

3. Press

Locate/OK

[5] to save settings or

Exit

[SK] to cancel.

B. Alert Mode

While tracing a cable or pipe, it is possible to search for markers.

1. Press

Alert

[SK].

− If the unit is in Dir Pk, DirNull or Ind Pk,

a prompt will notify the operator that alert

mode only functions in Special Peak

(Spl Pk) mode.

2. Press

Mode

[SK Toggle] for Spl Pk.

3. Press

Alert On

[SK Toggle].

Содержание Dynatel 2250M


































































Результаты поиска

Содержание Dynatel 2250M

Отзывы:

Похожие инструкции для Dynatel 2250M

Бренды по названию

Популярные бренды

3M Dynatel 2250M, Руководство оператора

Результаты поиска

Содержание Dynatel 2250M

Отзывы:

Похожие инструкции для Dynatel 2250M

Бренды по названию

Популярные бренды