3M Dynatel 2250M Скачать руководство пользователя | Manualshive

Страница: 9 / 65

background image

78-8130-6150-0-F

9

B. Receiver Battery Installation

Remove cap from receiver handle.
Install eight ‘AA’ size alkaline cell batteries (LR6) into the battery holder as indicated by

the polarity symbols (+ and –).
Attach battery holder to the PP3 connector in the receiver handle, and slide holder into

the handle. Replace the cap.

8 “AA” (LR6) Alkaline Batteries

1. Twist cap to open battery

compartment.

2. Slide battery compartment

out of handle.

m

Caution

To reduce the risks associated with fire and explosion:

•  Do not short, excessively heat, or dispose of batteries in fire.
•  Install batteries with proper polarity.
•  Use only Alkaline "AA" (LR 6) sized batteries.
•  Do not charge batteries
•  Do not use leaking batteries

To reduce the risks associated with environmental contamination:

•   Dispose of batteries and electronic components in accordance with all regulations.
•  Ensure batteries are installed with correct polarity.
•  Always remove batteries when storing the units for long periods of time.

The receiver batteries are tested for two seconds every time the unit is turned on.

The bar graph on the display will fill to the relative battery level.
The Battery Icon [8] on the Locating Displays will continuously indicate the battery

level.

«
...
7
8
9
10
11
...
»

Содержание Dynatel 2250M


































































Отзывы:

Нет отзывов

Похожие инструкции для Dynatel 2250M

Бренд: idiag Страницы: 10

Бренд: Bandit Страницы: 136

Versaflo S Series

Бренд: 3M Страницы: 11

DBI Sala EXOFIT

Бренд: 3M Страницы: 32

Бренд: 3M Страницы: 8

Бренд: Accurate Bio-Medical Technology Страницы: 35

Бренд: B. Braun Страницы: 2

Aesculap Neurosurgery

Бренд: B. Braun Страницы: 13

Aesculap AdTec mini

Бренд: B. Braun Страницы: 2

Бренд: B.Well Страницы: 2

Бренд: B. Braun Страницы: 55

BA Ultimate LED

Бренд: B.A. International Страницы: 234

Бренд: Nemalux Страницы: 6

Бренд: OBDLink Страницы: 2

Бренд: Major tech Страницы: 12

Бренд: quadient Страницы: 188

Бренд: Radarsign Страницы: 16

Бренд: Vahterus Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды