3M 9800 страница 27 Скачать руководство пользователя | Manualshive

Страница: 27 / 52

background image

3M

Overhead Projector 9800 Series

Section 5 – Disassembly/Reassembly

5-2

9800 Service Manual

3M 1996

5-1-1. How to Replace the Mirror Assembly

Caution

!

Do not remove the protective film until the Mirror
is installed. This is a front-surface mirror and
should not be touched.

Caution

!

Be careful not to damage the inside of the lens
while installing the mirror.

1. Remove retaining screw from head cover.

Figure 5-2.

2. Lift up at back of head cover (A) and slide

forward (B).

3. Spread cover (C) to free it from the lens bracket.

4. Lift head cover (D) over mirror to remove it and

expose the projection mirror and lens bracket.

9800–69I

2

3

4

1

4

5

5

Figure 5-2. Removing the Head Cover

5. Remove mirror retaining screws, clip and plastic

washer on each side to free the mirror from the
lens bracket. Figure 5-1.

6. Reassemble in reverse order.

Note

When attaching the new mirror, remember to
place the plastic washer between the lens
bracket and clip. Apply 4-5 in.-lbs. of torque
to mirror retaining screws.

7. Remove protective film from the Mirror.

5-1-2. How to Replace the Triplet Lens

1. Remove head cover and mirror assembly. See

Section 5-1-1.

Caution

!

Be careful not to scratch the mirror while
installing the triplet lens.

2. Unscrew three lens retaining screws to free lens.

Figure 5-1.

3. Lift lens upward to remove from lens bracket.

4. Reassemble in reverse order.

«
...
25
26
27
28
29
...
»

Содержание 9800





















































Отзывы:

Нет отзывов

Похожие инструкции для 9800

Бренд: NEC Страницы: 6

Бренд: NEC Страницы: 6

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 2

LT154 - MultiSync UXGA DLP Projector

Бренд: NEC Страницы: 2

LT154 - MultiSync UXGA DLP Projector

Бренд: NEC Страницы: 8

LT100 - MultiSync XGA DLP Projector

Бренд: NEC Страницы: 5

LT150Z - MultiSync XGA DLP Projector

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 8

GT950 - MultiSync XGA LCD Projector

Бренд: NEC Страницы: 2

DLP CINEMA NC1600C

Бренд: NEC Страницы: 57

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 2

Бренд: Panamax Страницы: 4

Бренд: Samsung Страницы: 89

Бренд: Samsung Страницы: 57

Бренд: Nectre Fireplaces Страницы: 232

Ceiling Trim Kit for Home2 Series

Бренд: Elite Screens Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды