3M 9800 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 52

3M 9800 Скачать руководство пользователя страница 29

3M

Overhead Projector 9800 Series

Section 5 – Disassembly/Reassembly

5-4

9800 Service Manual

3M 1996

5-2-3. How to Replace the Top Cover Latch

1. Open top cover.

2. Use a screwdriver to gently spread apart the hinge

holders securing the top cover latch. See
Figure 5-6.

3. Pull latch out to remove.

4. To insert latch, align tension spring and slip one

side of the latch into hinge holder. Use a screw
driver to gently spread apart the other hinge
holder and snap the other side of the latch into
place.

Note

There is a tension spring (not shown) attached
to the plastic peg on the back side of the latch.

Figure 5-6. Top Cover Latch

5-2-4. How to Replace the Stage Glass

1. Remove the Fresnel Lens. See 5-2-2.

2. Carefully remove the damaged glass.

3. Remove the metal retainer to free the glass.

Figure 5-4.

4. When replacing the stage glass, make sure the

beveled edges are under the plastic nibs on the top
side of the top cover. See Figure 5-7.

Nibs

Figure 5-7. Replacing Stage Glass

5. Stand the top cover on edge and attach the metal

retainer.

6. Clean the underside glass surface before

reinstalling the Fresnel Lens.

«
...
27
28
29
30
31
...
»

Содержание 9800





















































Отзывы:

Нет отзывов