3M 9800 Скачать руководство пользователя страница 41

Страница: 41 / 52

Overhead Projector 9800 Series

Section 5 – Disassembly/Reassembly

5-16

9800 Service Manual

3M 1996

5-5.

Fan Blade/Fan Motor

5-5-1. How to Replace Fan Blade and Motor

Unplug projector power cord before performing
any maintenance to electrical components.

1. Unplug power cord from outlet.

2. Unscrew five fan assembly retaining screws on

bottom of projector. Figure 5-32.

9800-87I

Fan
Assembly
Screws

Rubber
Foot

Bottom View of Projector

ÅÅ

Ventilation
Slots

Figure 5-32. Fan Assembly Retaining Screws

3. Disconnect wire connectors and remove fan/blade

assembly from projector body. Figure 5-33.

4. Reassemble in reverse order.

Note

The fan assembly has five vibration isolation
pads on the bottom of the mounting bracket
and heat tape on the side toward the lamp
assembly.

5. Tighten the fan assembly retaining screws with

7-8 inch–pounds of torque.

Important

Do not over tighten the retaining screws.
Excess torque will flatten the vibration
isolation pads.

Caution

Be sure that wires are not pinched when
reassembling.

Fan Blade

Mounting
Bracket

Motor

9800-76I

Vibration
Pad

Heat Tape

Ground
Wire

Figure 5-33. Fan/Blade Assembly

Note

The fan/blade assembly is a complete unit and
cannot be disassembled.

Содержание 9800





















































Результаты поиска

Содержание 9800

Отзывы:

3M 9800, Руководство по обслуживанию, Страница: 41 / 52

Результаты поиска

Содержание 9800

Отзывы: