3M 9800 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 52

3M 9800 Скачать руководство пользователя страница 15

3M

Overhead Projector 9800 Series

Section 2 – Operating The 9800 Projector

2-4

9800 Service Manual

3M 1996

2-4.

Lamp Changer System

When a lamp burns out, a red X (Figure 2-9) will

appear on the closed control panel door.

9800-83I

Figure 2-9. Control Panel Door Closed

1. Open control panel door (1). Figure 2-10. Power

to lamp is disconnected by lamp interrupt switch
(2) in door.

Note

The red LED lamp (5) will light if the selected
lamp (position 1 or 2) is burned–out or
missing.

5

Figure 2-10. Control Panel Door Open

2. Rotate the Lamp Changer Dial (3) to position 1 or

2.

3. Close control panel door to restore power and

illuminate lamp.

Note

The red X will light when a lamp is either
defective or missing.

Important

Lamp will not illuminate unless control
panel door is closed.

2-5.

High/Low Lamp Setting

Activate the High/Low switch to select High (bright)
or Low (normal) lamp illumination.

1. Open control panel door (1). Power to lamp is

disconnected by interlock (2) in door.
Figure 2-10.

2. Depress High/Low switch (4) to set desired

brightness.

a.

= High: Brightest image, shorter lamp life

b.

= Low: Normal image, longer lamp life

Note

Operating the projector in the “low” setting
will extend lamp life.

3. Close control panel door to test lamp brightness.

«
...
13
14
15
16
17
...
»

Содержание 9800





















































Отзывы:

Нет отзывов