3DHISTECH TMA Grand Master 2.6 Скачать руководство пользователя страница 77

Страница: 77 / 92

TMA Grand Master 2.6 – User’s Guide

5 Using TMA Grand Master

Labeling direction (increasing/decreasing)can be set for rows and columns separately by
clicking .

•

Labeling position

Select one of the positioning modes

Align to block edges

Align to core position

Barcode

Tick

Enable automatic function

to set the identifiable type of barcode that is specified

manually (select

Manual

) or activate Autodetect to allow the program the automatic

identification without specifying the barcode type, thus blocks with any kind of barcode will

be identified during creating a project.

For software versions older than 2.6 the default barcode reader is selectable after the
upgrade. Select

VintaSoft

to process barcodes with the embedded reader or

Matrox

to work

with MIL dongle.

December 9, 2016 – Rev. 1

3DHISTECH Ltd.

77(92)

Содержание TMA Grand Master 2.6





























































































Результаты поиска

Содержание TMA Grand Master 2.6

Отзывы:

Бренды по названию

Популярные бренды

3DHISTECH TMA Grand Master 2.6, Руководство пользователя

Результаты поиска

Содержание TMA Grand Master 2.6

Отзывы:

Бренды по названию

Популярные бренды