background image

B-4

A

PPENDIX

 B: CLI COMMAND DESCRIPTION

Adds an entry to the IP routing table. IP packets destined for networks that match 
this network will be routed to this address. The command 

list ip routes

 displays 

your currently defined routes.

add ipx network

<network_name>

address [ipx_address] 

{ interface [eth:1] }

{ enabled [yes] }

frame  [ETHERNET_II | SNAP | DSAP | NOVELL_8023]

Adds an IPX network to the list of IPX networks available over the specified 
interface.

add ipx route

<ipx_net_address>

gateway [ipx_host_address]

metric [metric_number]

ticks [tick_number]

Adds an IPX static route (for the LAN) to the system’s IPX Route table, which 
defines static routes to remote IPX networks. The command 

list ipx routes

 displays 

currently defined static routes. 

Parameters

Description 

<net_address> IP address of the remote network, in the format nnn.nnn.nnn.nnn, with or 

without a mask specifier. The Mask Specifier can be ‘A’, ‘B’, ‘C’, or ‘H’, or a 
numeric value from 8 to 30 that describes the number of one bits in the mask. 
If you do not specify a mask, the system will generate it from the network 
address.

gateway

IP address of gateway used to reach this remote network.

metric

An integer representing how far away the route is, in “hops” through other 
routers. Values are 1-15.

Parameters

Description 

<network_name> Name of IPX network. A unique ASCII string of up to 32 characters; space 

must be surrounded by double quotes.

address

Address of the IPX network.

interface

Name of the interface with which this IPX network is to be associated. The 
default is the first LAN interface (

eth:1

).

enabled

Optional parameter indicates whether the network is enabled (YES) or 
disabled (NO) by this command. YES is the default.

frame

Frame encapsulation chosen for this IPX network. 

Parameters

Description

<ipx_net_address>

IPX network address requiring a route.

gateway

IPX address of the host which will act as a gateway. The format is 
nnnn.xx:xx:xx:xx:xx:xx (net_addr.mac_address).

metric

Number of “hops” through different routers needed to reach the remote 
IPX network.

ticks

Estimated interval in ticks it takes to deliver a packet to the remote 
network. There are approximately 18 ticks per second.

Содержание OfficeConnect 3CP4144

















































































































































Отзывы: