Set Commands
12-21
.
set ip routing
Sets global parameters for IP routing on the specified IP router address which
serves as the gateway to an autonomous system. This command has the following
parameters:
autonomous_system_number
<number>
metric_maximum_entries
<number>
rip_flags
<metrics, send_request>
router_id
<IP_address>
IP routing must be disabled before setting these values.
An autonomous system is a connected group of networks run by one or more
network operators which has a single and clearly defined routing policy. An
autonomous system number is a unique identifier for such a system, but is not
currently supported by the OfficeConnect Gateway
.
Parameters
Description
<IP hostname or
IP network address>
IP address or host name of the remote destination, in the format
nnn.nnn.nnn.nnn
, entered
with
or
without
a mask specifier. The mask
specifier can be ‘A’, ‘B’, ‘C’, or ‘H’ (host), or a numeric value from 8 to
30 (32 if a host) that describes the number of one bits in the mask.
You can also specify the netmask in the
xxx.xxx.xxx.xxx
format. If you
do not specify a mask, the system will self-generate it (based on the
network address) for all routes except
host
routes, for which you
must
specify a mask.
gateway
Host name or IP address of the next hop to the specified IP network
address
metric
Number of hops the destination is removed from the specified IP
network address. The range is
1-15
.
Parameters
Description
autonomous_system_number
Value associated with a protocol not currently supported.
Disregard this value. The range is
1-65535
.
metric_maximum_entries
Most next hop entries the Next Hop Hash Table can hold. The
default is
512.
The range is
256-65535
.
router_id
IP address of the OfficeConnect Gateway. If value not
specified, the system will take a user-configured
internal
IP
address for this value, or the
eth:1
value if no internal value is
specified.
rip_flags
Flags indicate at which level a RIP instance is disabled or
configured. Choices are:
Metrics
- Specifies how to increment metrics using
RFC1058.
Send_request
- Sends a RIP request for routing data
when an interface first comes up.
Содержание OfficeConnect 3C100XF
