2Wire MEMO2 WS.502 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 35

2Wire MEMO2 WS.502 Скачать руководство пользователя страница 5

Manual WS.502 v1.5

2-Wire Energy Monitor

4

Once logged in:

Click

'CONFIGURATION':

the following

menus

appear:

Start

with '

SETTINGS

':

We start by checking the network settings. If 'DHCP' is
checked, it must be checked out, otherwise there is a
chance that a different IP address will be assigned at
the next start-up. You can always change the address
or port number if necessary.

As an example:

192.168.0.123

and port number

8080

.

Please note

that when you change this address, you

will need to write down what the new address and
port number is! After sending, you no longer have
communication and you have to start in the browser
with the new IP address and port number.

Press

'SEND CONFIG'

After a second confirmation, you must enter the new
address and port number in your web browser. If
there is communication, the new institution has
succeeded.

Now we have to surf to 192.168.0.123:8080 and then
the address setting succeeded.

Would you rather work with DHCP:

have an IP

address automatically awarded via a 'DHCP

server'

Tick

'DHCP'

and press

'SEND

CONFIG'.

After a short waiting period, a new IP address will be
assigned to your web server. (In this example
192,168,0.164 : 8080)

Write down this new address and press the
confirmation button again.

From now on, there is no communication at your
former IP address.

In the toolbar, type the newly assigned address to get
back connected.

Go back to

'CONFIGURATION'

->

'SETTINGS'

GATEWAY-SUBNETMASK-DNS SERVER

There must be internet on your web server, otherwise
there are no charts to see, and you can't send logs to
a remote FTP server so important that also
'GATEWAY', 'SUBNETMAK' and 'DNS SERVER' are
entered correctly

«
...
3
4
5
6
7
...
»

Содержание MEMO2 WS.502




































Отзывы:

Нет отзывов