2Wire MEMO2 WS.502 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 35

2Wire MEMO2 WS.502 Скачать руководство пользователя страница 21

Manual WS.502 v1.5

2-Wire Energy Monitor

20

0 : normal graph or temperature display such
as standard module (e.g. electra = V-A-W-Wh)

1: CREDIT chart (when using 'CREDIT' module
in logic)

2: electra: 4 graphs only for display voltages
or temperatures (V or °C)

3: electra: 4 charts only for display flows (A)

4: electra: 4 charts only for display power
(kW)

5: electra: 4 charts only for display hourly
consumption (kWh)

LIMITER:

with this logic module, a limit can easily be imposed
on consumers. The aim is to set a limit on power,
hourly consumption or daily consumption.

When this limit is exceeded, a relay module can
disable the load for a certain amount of time, and
switch it back on after a set time.

TOP:

CHANNEL MODULE SELECTION:

•

NC

:

Mode1

:Power, Hour Consumption and

Day Consumption measurements come from
external module(s)

•

CH0-63

:

Mode2

: Power, Hour Consumption

and Day Consumption measurements come
from the selected measurement module.

Inputs:

Mode1: Indian ModuleChannel - NC:

•

P Max = external measurement Power (can
have multiple power measurements via ADD
module).

•

HC Max: External measurement Hour
Consumption (can have multiple HC
measurements via ADD module).

•

DC Max: External Measurement Day
Consumption (can have multiple DC
measurements via ADD module).

•

Timer: If a 'variable' timer is desired, this input
can be connected to (for the time being) a
'dimmer', which determines the time how
long the 'power overload' should remain
active.

The measured values are compared in 'OR-LOGIC'
with the internal compare values.

Mode2: If ModuleChannel is active (only for log
channels, with power, hour and day consumption
outputs available vb. EMMxx, P1poort...)

•

P Max = external compare value for Power (1-
65000W) via dimmer or other reference
values.

•

HC Max: external compare value (1-65000
Wh) for Hour Consumption (ditto).

•

DC Max: external compare value (1-65000
kWh) for Day Consumption (ditto).

•

Timer: If a 'variable' timer is desired, this input
can be connected to (for the time being) a
'dimmer', which determines the time how
long the 'power overload' should remain
active (10-255min).

Bottom:

•

RELAY CHANNEL 0-63

SELECTOR:

«
...
19
20
21
22
23
...
»

Содержание MEMO2 WS.502




































Отзывы:

Нет отзывов