2Wire MEMO2 WS.502 Скачать руководство пользователя страница 10

Страница: 10 / 35

Manual WS.502 v1.5

2-Wire Energy Monitor

Other modules such as EMM.120... 630 do not have
SerialNr, but only Modbus addresses (range 1-247).
However, only serialnrs canbe used in the
projectammation.

That's why we're going to make a

fictitious

serial

number

for these

modules

ourselves.

Most

modbusmodules only need one channel, except for
the more complex modules such as the EMM.630 or
calorie meters. Those modules have 3 or more
channels (e.g. 3 phases) .

The maximum is 8

channels per module. (08xxxxxx)

The first two digits of the serial number shall
determine the number of outputs/entries:

'01' are for single-rigid meters

'02' are for single-rigid meters, which
measures in both directions (import-export)

'03' are for three-legged meters

You can choose the following 5 digits yourself, but
make sure the serial number remains 'unique'!

Examples for the EMMxxx energy modbus meters
series:

Enkelfasige (enkel import): EMM120

–

EMM220 :

01E

00001….

01E

99999

Enkelfasige ( export) : EMM220 :

02E

00001…

02E

99999

Three-rate: EMM630

–

EMM630CT:

03E

00001....

03E

99999

Caloriemeters :

03U

00001...

03U

99999

Kamstrup : 03K00001... 03K99999
areconfigured by 2-Wire

The limit of the number of log channels is 64 and the
limit of the number of modules is 32.

The first serial number we are going to enter in the
field

'SerialNr'.

In the 'Module

Name'

field, one can

enter a name related to the module. (e.g. distribution
cabinet garage... thermostat..) When we press

'NEW'

now, the typed serial no. is put in the 'list

box'.

On the right side of the picture, a module will appear
with a number of channels according to our serial
number

(e.g. 01E00001 = 1 channel. )

: stands for 'CHANNEL' and is automatically

generated by the web server. This channel No
will later serve to make the link between log
channel and (modbus) address. (see below).

MODE:

(Counter, Thermostat, AirQ....) is

automatically dialed

ADDR:

Each channel must have a UNIQUE

ADDRESS

in the range 1-247. Therefore, no

channel may have the same address. Start
from 1 and number so that each meeting
entrance has a unique address. The simplest
is for

'ADDR'

to fill in the

same value

as the

channel number

'CH'.

When we have

modules without a serial number (series
EMMxxxx) we have to program these
addresses on these modules via the existing
display.

(How to change the address on the

module is described in the manual of the
module itself.)

UBAD

: for modules with multiple log

channels such as 3-fazen meters and calorie
meters there is always only 1 modbus
address, but with the subaddress you can log
different data:

For the EMMxxxx series:

serienr 01Exxxx : subadd = 0

series no 02Exxxx: both channels

SAME

MODBUS

ADDRESS,

subadres 0 (import) and

subadres 1 (export)

series no 03Exxxx: all 3 channels

SAME

MODBUS

ADDRESS

, subad = 0

–

1 - 2

PARA3: PARA6

: are specifically explained in

the manual of the modules. Nothing needs to
be filled in for the EMMxxx.

•

UNIT:

wordt soms automatisch ingevuld met

‘kWh, °C, ppm…’

Содержание MEMO2 WS.502




































Результаты поиска

Содержание MEMO2 WS.502

Отзывы:

2Wire MEMO2 WS.502, Руководство пользователя, Страница: 10 / 35

Результаты поиска

Содержание MEMO2 WS.502

Отзывы: