2Wire MEMO2 WS.502 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 35

2Wire MEMO2 WS.502 Скачать руководство пользователя страница 32

Manual WS.502 v1.5

2-Wire Energy Monitor

31

WIRELESSLY LINK MODULES VIA THE RF GATEWAY

Then go to the connected modbus module (e.g.
02E00001)

Press "CHANGE." 'Module NAME' fills in the SN of the
gateway

(e.g. 08G00091) Press "CONFIRM" and then press
"SEND." When a valid modbus address is filled in,
'Module OK' will appear.

If no valid address, 'Module not found' may appear.
Press 'TEST'. This feature only tests the RF
communication between gateway and the web server.

Further explanation of configuration RG.016 is in the
documentation gateway.

19. QUICK START

A shortened repetition of all steps:

1.

Connection power supply, bus and network
cable, which is connected to your local
network.

2.

Use server

scanner

toolto find out the IP

address and port number.

3.

Browse to this address and port number
(default 8080)

4.

Login withadminIP or admin2-WIRE and
password '2015'

5.

To change the IP address: to menu 'SETTINGS'
(see chapter 4)

6.

To make up users: to menu 'SETTINGS', old
login = 'loginold', old pass = '1234'

7.

Energy prices

:

to menu 'SETTINGS', bottom,

cost prices

8.

Create modules: to menu 'MODULES', type in
serial number, assign names, fill parameters
according to the type of module (see leaflet of
this module), send.

9.

Create channels: to menu 'CHANNELS', first
create groups (minimum 1), then possibly sort
channels, then divide the groups between the
channels.

10.

Main energy sources: if there are total
measurements, to menu 'CHANNELS', typing
channel numbers for electricity, gas, water,
fuel oil.

11.

Export energy sources: if there are total
measurements for export (solar panels), to
menu 'CHANNELS', type in this channel
number(s).

12.

EPC level calculation: if there is total
measurement of heating source(s), to menu
'CHANNELS', typing in this channel number(s)
and estimated area of the heated spaces.

13.

Go to 'EXIT' and test all channels. (Only after
the first hour are consumed logged)

«
...
30
31
32
33
34
...
»

Содержание MEMO2 WS.502




































Отзывы:

Нет отзывов