ZyXEL Communications VWG1312-B10A User Manual Download Page 142 | Manualshive

Page: 142 / 378

background image

Chapter 8 Home Networking

VMG1312-B10A User’s Guide

142

8.1.2 What You Need To Know

8.1.2.1 About LAN

IP Address

IP addresses identify individual devices on a network. Every networking device (including
computers, servers, routers, printers, etc.) needs an IP address to communicate across the
network. These networking devices are also known as hosts.

Subnet Mask

Subnet masks determine the maximum number of possible hosts on a network. You can also use
subnet masks to divide one network into multiple sub-networks.

DHCP

A DHCP (Dynamic Host Configuration Protocol) server can assign your Device an IP address, subnet
mask, DNS and other routing information when it's turned on.

DNS

DNS (Domain Name System) is for mapping a domain name to its corresponding IP address and
vice versa. The DNS server is extremely important because without it, you must know the IP
address of a networking device before you can access it.

RADVD (Router Advertisement Daemon)

When an IPv6 host sends a Router Solicitation (RS) request to discover the available routers,
RADVD with Router Advertisement (RA) messages in response to the request. It specifies the
minimum and maximum intervals of RA broadcasts. RA messages containing the address prefix.
IPv6 hosts can be generated with the IPv6 prefix an IPv6 address.

8.1.2.2 About UPnP

Identifying UPnP Devices

UPnP hardware is identified as an icon in the Network Connections folder (Windows XP). Each UPnP
compatible device installed on your network will appear as a separate icon. Selecting the icon of a
UPnP device will allow you to access the information and properties of that device.

NAT Traversal

UPnP NAT traversal automates the process of allowing an application to operate through NAT. UPnP
network devices can automatically configure network addressing, announce their presence in the
network to other UPnP devices and enable exchange of simple product and service descriptions.
NAT traversal allows the following:

• Dynamic port mapping
• Learning public IP addresses

«
...
140
141
142
143
144
...
»

Summary of Contents for VWG1312-B10A



























































































































































































































































































































































































Reviews:

No comments

Related manuals for VWG1312-B10A

Brand: TANDBERG Pages: 58

PremierWave 2050

Brand: Lantronix Pages: 73

Brand: Lantronix Pages: 2

Brand: RTA Pages: 66

Brand: BAB TECHNOLOGIE Pages: 52

Brand: Eaton Pages: 2

Brand: Pathway connectivity solutions Pages: 14

Brand: Pace Pages: 19

Brand: CastleNet Pages: 29

Brand: Yeastar Technology Pages: 10

easyconnect ec350

Brand: Netbiter Pages: 40

Brand: NETGEAR Pages: 53

P-661HW-D Series

Brand: ZyXEL Communications Pages: 146

Brand: NKE Pages: 14

Brand: Profibus Pages: 42

Brand: Humanscale Pages: 2

WIRELESS DATA GATEWAY

Brand: Paradyne Pages: 66

KonNad C2000-D2-DCTZ02

Brand: SinoCon Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands