manualshive.com logo in svg

ZyXEL Communications GS1200 SERIES, User Manual, Page: 56 / 85

Share
Download
ZyXEL Communications GS1200 SERIES User Manual Download Page 56

Chapter 11 Mirroring

GS1200 Series User’s Guide

56

The following table describes the labels in this screen.

Table 11   Mirroring

LABEL

DESCRIPTION

Port Mirroring

Port Mirroring

Select 

Enable

 to activate port mirroring on the Switch, or 

Disable

 to disable the feature.

Mirror Direction

Specify the direction of the traffic to mirror by selecting from the drop-down list box. Choices 
are 

Egress

 (outgoing), 

Ingress

 (incoming) and 

Both

.

Port

This field displays the port number.

Monitor Port

The monitor port is the port you copy the traffic to in order to examine it in more detail without 
interfering with the traffic flow on the original ports.

Note: Select one monitor port.

Mirrored Port

Select this option to mirror the traffic on a port.

Note: Select one or multiple mirrored ports.

Apply

Click this button to save your changes to the Switch.

Summary of Contents for GS1200 SERIES






















































































Reviews:

No comments