manualshive.com logo in svg

ZyXEL Communications GS1200 SERIES, User Manual, Page: 22 / 85

Share
Download
ZyXEL Communications GS1200 SERIES User Manual Download Page 22

Chapter 4 Web Configurator

GS1200 Series User’s Guide

22

4.3.1  Change Your Password

After you log in for the first time, you must enter a new password using the keyboard characters ("a – z", 
"A – Z", "0 – 9"). The password must be 8 to 15 characters long. Click 

Management

 to display the next 

screen to change your login password.

For GS1200-5HP and GS1200-8HP, you can enter the default password 

1234

 again, if you do not want to 

change your password.

Figure 17   

Change Administrator Login Password

4.4  Switch Lockout / Resetting the Switch

You could block yourself (and all others) from managing the Switch if you do one of the following:

1

Remove all ports from VLAN1 and you do not configure other VLAN groups.

Link Aggregation

This link takes you to screens where you can logically aggregate physical links to form one 
logical and higher-bandwidth link.

Mirroring

This link takes you to a screen where you can copy traffic from one port or ports to another port 
so that you can examine the traffic from the first port without interference.

QoS

This link takes you to a screen where you can configure port-based or IEEE 802.1p QoS. The 
Switch can put packets into the queues according to the port on which the packet is received 
or the priority tag in the packet.

IGMP Snooping

This link takes you to a screen where you can configure IGMP snooping. You must enable IGMP 
snooping to use the IPTV service. It checks the IGMP packets passing through it, picks out the 
group registration information, and configures multicasting accordingly.

Traditionally, packets are transmitted in one of either two ways – Unicast (one sender to one 
recipient) or Broadcast (one sender to everybody on the network). Multicast delivers packets 
to just a group of hosts on the network.

Management

This link takes you to screens where you can change the system login password, perform 
firmware upgrade and configuration file maintenance as well as reset/reboot the system. You 
can also configure the IP address and subnet mask, set management VID, and enable IEEE 
802.3az EEE.

Table 4   Navigation Panel Links (continued)

LINK

DESCRIPTION 

Summary of Contents for GS1200 SERIES






















































































Reviews:

No comments