manualshive.com logo in svg

ZyXEL Communications GS1200 SERIES, User Manual, Page: 52 / 85

Share
Download
ZyXEL Communications GS1200 SERIES User Manual Download Page 52

GS1200 Series User’s Guide

52

VLAN ID

This is the ID number of the VLAN group.

Enter a number between 1 and 4094 as the VLAN ID.

01 – 08

01 – 05

This displays the ports that are participating in a VLAN. A tagged port is orange, an untagged 
port is green and ports not participating in a VLAN are gray. Multiple ports in a VLAN can be 
configured as tagged or untagged or not participating.

A port is a ‘tagged port’ when the interface is expecting frames containing VLAN tags. An 
example of this is when the sender will send a frame with a VLAN tag. The receiving switch will 
see the VLAN tag, and if the VLAN is allowed, it will forward the frame.

Modify

Click 

Modify

 to edit the VLAN settings. 

Delete

Click 

Delete 

to remove the VLAN group. You cannot delete the default VLAN.

Create New VLAN

Click this button to configure a new IEEE 802.1Q VLAN for the Switch.

Table 9   VLAN (continued)

LABEL

DESCRIPTION

Summary of Contents for GS1200 SERIES






















































































Reviews:

No comments