background image

Problem

Corrective Action

“Device Not Communicating” posted in plumbSMART

Step 1

Verify batteries installed in LoRa Monitor electronics and have 

sufficient charge.  Install new batteries, as needed.  Alert on 

product’s page in plumbSMART should clear within 1 hour or on 

next faucet activation. (Refresh web page by clicking on reload 

icon in the browser to clear the alert.) 

Step 2

If problem still present, verify gateway is within range of LoRa 

Monitor and functioning (see Gateway Troubleshooting section)

Step 3 

If problem still present, verify plumbSMART subscription status 

on product page’s Details tab listed as “Activated” 

NETWORK:  

Senet

SUBSCRIPTION STATUS: 

Activated

LAST HEARD FROM: 

07/14/2020, 04:29 PM CDT

If listed as “Deactivated”, contact Zurn Custom Service at 1.855.

ONE.ZURN (1.855.663.9876) for assistance.

“Status – Good” posted in plumbSMART and faucet not 

actuating 

Step 1

Verify LoRa Monitor’s cables are connected to IR sensor 

and Faucet actuator electronics.  Restore proper electrical 

connection, as needed.

Step 2 

Test activate the faucet.

If problem persists, see Faucet Troubleshooting section in this 

guide for other steps.

“Status – Good” posted in plumbSMART and faucet actuates but 

usage event data not appearing in plumbSMART Charts

Step 1

Verify gateway is powered and LoRa Status LED is ON.  If 

not, apply power per Zurn Gateway Installation Guide or see 

Gateway Troubleshooting section in this guide of other steps.

Step 2

If problem still present, verify plumbSMART subscription status 

on product page’s Details tab listed as “Activated” 

NETWORK:  

Senet

SUBSCRIPTION STATUS: 

Activated

LAST HEARD FROM: 

07/14/2020, 04:29 PM CDT

If listed as “Deactivated”, contact Zurn Customer Service at 

1.855.ONE.ZURN (1.855.663.9876) for assistance.

Step 3

If problem still present, the LoRa Monitor electronics may be 

faulty.  Contact Zurn Customer Service at 1.855.ONE.ZURN 

(1.855.663.9876) for assistance with additional troubleshooting 

steps and, if needed, unit replacement.

Trouble Shooting: LoRa Monitor

For further assistance with troubleshooting, visit https://plumbsmart.zurn.com/app/training

Summary of Contents for AquaSense ZER-W2 Series













Reviews: