Zte AD3812 Command Manual Download Page 34

Page: 34 / 71

WCDMA Module

+COPS=?

+COPS: [list of supported (<stat>,long
alphanumeric <oper>

,short alphanumeric <oper>,numeric
<oper>[,< AcT>])s]

[,,(list of supported <mode>s),(list of
supported <format>s)]

+CME ERROR: <err>

Defined values

<mode>

：

0 automatic (<oper> field is ignored)

1 manual (<oper> field shall be present, and <AcT> optionally)

2 deregister from network

3 set only <format> (for read cCOPS?), do not attempt
registration/deregistration (<oper> and <

AcT> fields are ignored); this value is not applicable in read command response

4 manual/automatic (<oper> field shall be present); if manual selection fails,
automatic mode (<mode>=0) is

entered

<format>:

0 long format alphanumeric <oper>

1 short format alphanumeric <oper>

2 numeric <oper>

<oper>: string type; <format> indicates if the format is alphanumeric or numeric;
long alphanumeric format can

be upto 16 characters long and short format up to 8 characters (refer GSM MoU
SE.13 [9]); numeric format is

the GSM Location Area Identification number (refer TS 24.008 [8] subclause
10.5.1.3) which consists of a three

BCD digit country code coded as in ITU-T E.212 Annex A [10], plus a two BCD
digit network code, which is

administration specific; returned <oper> shall not be in BCD format, but in IRA
characters converted from

BCD; hence the number has structure: (country code digit 3)(country code digit
2)(country code digit 1)(network

code digit 3)(network code digit 2)(network code digit 1)

<stat>:

0 unknown

1 available

2 current

3 forbidden

<AcT> access technology selected:

0 GSM

1 GSM Compact

2 UTRAN

Summary of Contents for AD3812








































































Search results

Summary of Contents for AD3812

Reviews:

Brands by name

Popular brands

Zte AD3812, Command Manual

Search results

Summary of Contents for AD3812

Reviews:

Brands by name

Popular brands