manualshive.com logo in svg

Zte AD3812, Command Manual

Share
Download
Zte AD3812 Command Manual Download Page 18

 

                                                                                                                                                    WCDMA Module 

 

17

+CRLP=[<iws>[,<mws>[,<T1>[,<N2
>[,<ver>[,<T4>]]]]]] 

 

+CRLP?  

+CRLP: 
<iws>,<mws>,<T1>,<N2>[,<ver1>[,<T4>
]] 

[<CR><LF>+CRLP: 
<iws>,<mws>,<T1>,<N2>[,<ver2>[,<T4>
]] 

[...]] 

 

Command

 

 

+CRLP=? 

 

+CRLP: (list of supported <iws>s),(list of 
supported <mws>s), 

(list of supported <T1>s),(list of 
supported <N2>s)[,<ver1> 

[,(list of supported <T4>s)]] 

[<CR><LF>+CRLP: (list of supported 
<iws>s),(list of supported 

<mws>s),(list of supported <T1>s),(list of 
supported <N2>s) 

[,<ver1>[,(list of supported <T4>s)]] 

[...]] 

 

Defined values

 

 

<ver>, <ver

x

>: RLP version number in integer format; when version indication is 

not present 

NOTE 2: Versions 0 and 1 share the same parameter set. Read and test 
commands shall return 

set (where <ver

x

> is not present). 

<iws>, <mws>, <T1>, <N2>, <T4>: IWF to MS window size, MS to IWF window 
size, acknowledgement 

T1, retransmission attempts N2, re-sequencing period T4 in integer format 
(default values 

depend on RLP version; refer 3GPP TS 24.022 [18]): T1 and T4 are in units of 
10 ms. 

 

3.7  +CR Service reporting control 

Description

 

 

Set command controls whether or not intermediate result code +CR: <serv> is 
returned from the TA to the TE. If 

enabled, the intermediate result code is transmitted at the point during connect 
negotiation at which the TA has 

determined which speed and quality of service will be used, before any error 
control or data compression reports are 

transmitted, and before the intermediate result code CONNECT is transmitted. 

+CR=[<mode>] +CR? 

 

+CR=?  

+CR: <mode> 

Command

 

 

+CR? 

+CR: (list of supported <mode>s)   

Defined values

 <mode>: 

Summary of Contents for AD3812








































































Reviews:

No comments

Brands by name

Popular brands

Load more brands