Zte AD3812 Command Manual Download Page 22

Page: 22 / 71

WCDMA Module

3.13 +VTD Tone duration

Description

This refers to an integer <n> that defines the length of tones emitted as a result
of the +VTS command. This does not

affect the D command. A value different than zero causes a tone of duration
<n>/10 seconds. The value zero causes a

"manufacturer specific" value.

+VTD=<n> +VTD?

<n>

+VTD=? (list of supported <n>s)

Command

+VTD=<n> +VTD?

<n>

Defined values

<n>:

0 mute off

1 mute on

3.14 +VTS DTMF and tone generation

Description

This command allows the transmission of DTMF tones and arbitrary tones (see
note). These tones may be used (for

example) when announcing the start of a recording period. The command is
write only. In this profile of commands,

this command does not operate in data or fax modes of operation
(+FCLASS=0,1,2-7).

+VTS=

as above

Command

+VTS=? (list

Defined values

1. <DTMF>. A single ASCII character in the set 0-9, #,*,A-D. This is interpreted
as a single ACSII character whose

duration is set by the +VTD command.

NOTE 2: In GSM this operates only in voice mode.

2. [<tone1>,<tone2>,<duration>]. This is interpreted as a dual tone of
frequencies <tone1> and <tone2>,

lasting for a time <duration> (in 10 ms multiples).

NOTE 3: This does not operate in GSM.

3. {<DTMF>,<duration>}. This is interpreted as a DTMF tone of different
duration from that mandated by the

+VTD command.

3.15 +CLCC List current calls

Description

Returns list of current calls of MT. If command succeeds but no calls are
available, no information response is sent to

Summary of Contents for AD3812








































































Search results

Summary of Contents for AD3812

Reviews:

Brands by name

Popular brands

Zte AD3812, Command Manual

Search results

Summary of Contents for AD3812

Reviews:

Brands by name

Popular brands