manualshive.com logo in svg

Zte AD3812, Command Manual

Share
Download
Zte AD3812 Command Manual Download Page 25

 

                                                                                                                                                    WCDMA Module 

 

24

3.17  +ZFLSH Send Flash/Flash with Information 

Descriptions 

The command is used to send a Flash/Flash with information to the base station, 

and it is usually used for call waiting and conference call. When receiving a call from a 
third party, use AT+ZFLSH command to send FLASH signals to switch between two 
differenct lines. If one FLASH signal is sent to the base station, the module will return 
with +ZFLSH. Please note that this doesn’t guarantee the switching between two lines 
for CDMA network because the network does not return the confirmation to the 
module. In a conference call, define the first called party as the first party, dial the first 
party, use AT+ZFLSH=< second called party’s number to call the second party, and 
the first party would automatically enter the call held status; once the second call is 
connected, use AT+ZFLSH command to realize the conference call. If you send a 
FLASH signal again, it will disconnect the call from the second party. Use ATH 
command to hang up all calls. 

Format 

AT+ZFLSH 

AT+ZFLSH=<phone number> 

ATD13333333333

；

 

Originate a voice call   

OK 

+ZCORG

：

13333333333 

+ZCCNT

：

3 

+CCWA

：

”26010681”,129    the second incoming 

call  

AT+ZFLSH 

Send a FLASH signal to 
switch to the second call   

OK 

+ZFLSH 

Not every switching is always successful   

Example 

ATH 

Release all calls   

OK 

+ZCEND

：

10 

ATD13316819064

；

 

Connect the first voice call   

OK 

+ZCORG

：

13316819064 

+ZCCNT

：

3 

AT+ZFLSH=26010681 

Hold the first call and dial the 
second call 

OK 

+ZFLSH 

AT+ZFLSH 

Realize a conference call   

OK 

+ZFLSH 

AT+ZFLSH 

Hold the second call and 
switch to the first call 

OK 

+ZFLSH 

（

parameter is a must

）

 

 

ATH 

Hang up all calls   

OK 

+ZCEND

：

10 

 

 

 

 

3.18  +VGT Transmit gain selection 

Description  The command is used to set MIC gain of currently selected audio path.   

Format AT+VGT=<MicGain> 

Example AT+VGT=2 

OK 

Summary of Contents for AD3812








































































Reviews:

No comments

Brands by name

Popular brands

Load more brands