Zte AD3812 Command Manual Download Page 21

Page: 21 / 71

WCDMA Module

3.10 +CVHU Voice Hangup Control

Description

Set command selects whether ATH or "drop DTR" shall cause a voice
connection to be disconnected or not. By voice

connection is also meant alternating mode calls that are currently in voice mode.
(See subclause 6.6).

+CVHU=[<mode>]

+CVHU? +CVHU:<mode>

Command

+CVHU=? +CVHU:(list

of supported <mode>s)

Defined values

<mode>:

0 "Drop DTR" ignored but OK response given. ATH disconnects.

1 "Drop DTR" and ATH ignored but OK response given.

2 "Drop DTR" behaviour according to &D setting. ATH disconnects.

3.11 +VGR Receive gain selection

Description

This refers to the amplification by the TA of audio samples sent from the TA to
the computer. The command operates

on an integer <n>, range 0...255. Values larger than 128 indicate a larger gain
than nominal. Values less than 128

indicate a smaller gain than nominal. The entire range of 0...255 does not have
to be provided. A value of zero implies

the use of automatic gain control by the TA.

+VGR=<n> +VGR?

<n>

+VGR=? (list of supported <n>s)

Command

+VGR=<n> +VGR?

<n>

3.12 +CMUT Mute control

Description

This command is used to enable and disable the uplink voice muting during a
voice call. Refer subclause 9.2 for

possible <err> values.

Test command returns supported values as compound value.

+CMUT=<n>

+CME

+CMUT? +CMUT:

Command

+CME ERROR:

Defined values

<n>:

0 mute off

1 mute on

Summary of Contents for AD3812








































































Search results

Summary of Contents for AD3812

Reviews:

Brands by name

Popular brands

Zte AD3812, Command Manual

Search results

Summary of Contents for AD3812

Reviews:

Brands by name

Popular brands