manualshive.com logo in svg

Zoom NUD360-F, Software User'S Manual, Page: 81 / 108

Share
Download
Zoom NUD360-F Software User'S Manual Download Page 81

Software User’s Manual    Ver.A1D-502-V8.03.30-NB 

81

 

5-6-6  Audio 

The section Audio is available only for audio-supported models. 

The user interface for audio control looks like as below: 

   

 

 

 

Parameters 

Description 

Audio In 

The  option 

“

Enabled

”

  would  activate  incoming  audio.  The 

option 

“

Disabled

”

  would  turn  off  the  incoming audio.  In  such 

case, the video stream is captured without audio.   

Microphone Type   

Select the type of microphone connected. 

Note:

 Available in vehicle-supported models only. 

Audio in Level   

For  vehicle-support  models,  use  this  function  to  adjust  the 
sensitivity level of audio input. 

Note:

 Available in vehicle-supported models only. 

Audio Out Volume 

The audio out volume level can be adjusted in the scale of 0-
100.  It  will  influence  the  volume  level  of  the  speakers 
connected to the camera. 

Note:

 Available only in camera models with audio out support. 

Audio Format 

Choose the compression format of audio: PCM, G.711A (A-law) 
or G.711U (

µ

-law). 

To  adjust  the  volume  level  of  the  speakers  connected  to  the  PC  that  runs  the  Web 

Configurator in order to hear the audio from the camera

’

s microphone or line-in device, 

go to Live View page and use the audio controls there: 

Audio Muted: 

 

Audio level adjusted to the maximum: 

 

This volume control appears in user interface only when the Audio-in function of  the 

camera has been 

“

Enabled

”

. 

 

 

or 

Summary of Contents for NUD360-F













































































































Reviews:

No comments