Zoom NUD360-F Software User'S Manual Download Page 15

Page: 15 / 108

Software User’s Manual Ver.A1D-502-V8.03.30-NB

Live View

This section describes how to configure the IP camera. The administrator has unlimited access

to all settings, while the normal user can only view live video.

Login

Initially there exists only administrator

’

s account in the camera (Account: Admin, Password:

123456)

–

you have to use that account to log in. You can later create normal user accounts

with limited access rights if necessary.

Feel free to choose your local language from the list of languages or keep it as English. After

pressing

“

”

, you will be able to access the user interface of Web Configurator.

Upon successful login, you will be able to see the Live View page. In case of Internet Explorer

browser, you may be prompted to allow the installation of ActiveX control from the camera.

Press

“

Install

”

then. The live video will appear shortly after that.

Summary of Contents for NUD360-F













































































































Search results

Summary of Contents for NUD360-F

Reviews:

Zoom NUD360-F, Software User'S Manual, Page: 15 / 108

Search results

Summary of Contents for NUD360-F

Reviews: