background image

Thu June 23, 2011  3:03 PM

Schedule Devices

Home

Menu OneTouch

Help

Back

Status

Filter Pump 
VSP Pump 
Spa 
Pool Heat 

 

Spa Heat 

 

Chiller 
Aux 1 
Aux 2 

 

Devices

Page

Down

Page

Up

 Select 

NOTE  Only one piece of equipment can be selected at 

a time. 

Second Step - Programming the new device

On the SCHEDULE screen, the added equipment will 

be displayed and highlighted in the circuit list. Also, the 

EDIT will be highlighted. 
Enter the day for the new device. Click SAVE when 

finished. 

Thu June 23, 2011  3:03 PM

Schedule

Home

Menu OneTouch

Help

Back

Status

Circuit 

Start Time  Stop Time 

Days

VSP 

7:00 AM 

6:00 PM 

Th, Wknd

Pool 

8:00 AM 

5:00 PM 

All

Spa 

7:00 PM 

10:00 PM 

F, Sa

Spa 

5:00 PM 

9:00 PM 

M, W

Spa Heat 

6:00 PM 

8:00 PM 

All

Pool Light 

6:00 PM 

8:00 PM 

All 

Page

Down

Page

Up   Save 

Run days

Start Time

Stop Time

 All 

Tu 

W

 Th 

Sa 

Su

 Week Days 

Weekends

  Add 

Edit 

Delete

Date

01/01/09

Time

10:00 PM

Home

Menu OneTouch

Help

Back

Status

  7 8 9
 4  5  6
 1  2  3
 0 

  Clear  Enter

Thu June 23, 2011  3:03 PM

Set Date/Time

Time:

 

00:00 

PM

 

Click ENTER when finished.

6.3 

Scheduling and Adding Devices

CAUTION

Make sure DATE and TIME are set up correctly 

before programming and scheduling any devices.

The SCHEDULE screen allows ON and OFF times to 

be programmed for any circuit (equipment) controlled 

by the AquaLink RS system. The circuit can be 

scheduled to turn ON or OFF all days, weekends, 

weekdays, or any specific day of the week (AquaLink 

RS). Each piece of equipment can be programmed for 

multiple (AquaLink RS) on/off times each day. 
Adding new devices to the circuit list on the 

SCHEDULE screen is a two-step procedure. First, you 

select and add the device to the circuit list and then you 

program it as desired.

First Step - Selecting the new device

MENU > SCHEDULE > SCHEDULE DEVICES

On the SCHEDULE screen, in the circuit schedule list, 

click the ADD button to display the screen below.
On the SCHEDULE DEVICES screen, in the DEVICES 

list, click the desired equipment. Then, click the 

SELECT button to save your selection and you will be 

automatically returned to the SCHEDULE screen.

Page 13

iAquaLink™ 

2.0

 Web Connect Device for AquaLink

®

 Control Systems   

|

   Installation Manual

ENGLISH

  

 

Summary of Contents for iAquaLink 2.0

















Reviews: