background image

Zip Hydroboil Plus - Installation & Operating Instructions - 85680 - February 2004

Page 11 of 16 

Depending on local water quality conditions and usage, the filter may require
changing every 6 to 12 months. You may also need to replace the filter if you
notice unpleasant odours or tastes, or if the flow rate of the tap is persistently
slow.

Some water may drip from the filter head (socket) and attached water lines
during replacement. Keep a bucket and towel handy to catch drips and mop up
any spills.

1. Locate service valve in the water supply line and turn off the water supply.

2. Grasp filter cartridge and twist right to left one quarter turn until it stops.

3. Ease cartridge downwards to detach it from the filter head (socket).

4. Do not tilt the cartridge as dirty water may spill from it if tilted.

5. Unpack replacement cartridge and write date where shown on the label.

6. Avoid bacterially contaminating cartridge top whilst inserting into head.

7. Align cartridge tabs with the slots on the under-side of the filter head.

8. Slide cartridge upward into head and rotate left to right until it stops.

9. Disconnect the filter hose from the heater inlet fitting and direct it into a

sink, bucket or similar receptical. Hold the tube in the receptical securely.

10. Open the service valve and flush the cartridge out to remove any loose

particles from the cartridge. When the water is clean and clear, shut the
service valve and reconnect the filter hose to heater inlet.

11. Open the service valve and check filter head for leaks. Refit if leaking.

12. Wipe up any spills and dispose of spent filter cartridge and packaging

thoughtfully.

Note: 

Freshly installed filters may cause water to appear milky. The water

should clear after running a few litres of water through the filter.

How to Replace the Filter

Filter Head

Filter Cartridge

To remove cartridge,
turn cartridge one
quarter turn right to
left, and draw
downwards.

To replace cartridge
align lugs on filter
cartridge with socket on
filter head. Push
upwards, turn one
quarter turn left to right
until secure

Summary of Contents for hydroboil plus

















Reviews: