Zimmer HRC-01 Series Installation And Operating Instructions Manual Download Page 11

Page: 11 / 44

INSTALLATION AND OPERATING INSTRUCTIONS:

2-jaw parallel gripper, electric, HRC-01/-02 series

DDOC00416 / a

EN / 2020-08-19

Zimmer GmbH

●

Im Salmenkopf 5

●



77866 Rheinau, Germany

●



+49 7844 9138 0

●



+49 7844 9138 80

●

www.zimmer-group.com

7. Installation

7.1 Safety notes

NOTICE:

Switch off the energy supply for the electronics before any assembly, installation or maintenance work.

►

Electronics may get damaged.

►

CAUTION:

Switch off the energy supply for the electronics before any assembly, installation or maintenance work.

►

Injuries are possible.

►

WARNING:

Risk of injury in case of unexpected movement of the machine or system into which the gripper is to be

installed.

►

Switch off the power supply to the machine before all work.

►

Secure the machine against being switched on unintentionally.

►

Check the machine for any residual energy.

7.2 General installation information

The gripper must be installed on a mounting surface in accordance with the specifications for flatness.

Length < 100 mm



permitted flatness imperfection < 0.02 mm

Length > 100 mm



permitted flatness imperfection < 0.05 mm

The mounting screws and the pins are included in the scope of delivery.

Strength class of the mounting screws ≥ 8.8 (DIN EN ISO 4762)

Observe the tightening torque of the mounting screws.

Make sure the mounting surface is sufficiently rigid and flat.

Refer to the technical data sheet for the exact positions.

7.3 Installing the mechanical system

The gripper is mounted on the robot arm using the adapter

flange

The following work steps must be observed during installa-

tion:

►

Loosen the grub screw

►

Remove the adapter flange

with the mounting

screws

►

Position the adapter flange

on the robot arm using

the straight pin

►

Mount the adapter flange

with the mounting screws

►

Insert the gripper

into the adapter flange

►

Re-mount the gripper

on the adapter flange

using

the grub screws

Summary of Contents for HRC-01 Series













































Search results

Summary of Contents for HRC-01 Series

Reviews:

Related manuals for HRC-01 Series

Brands by name

Popular brands

Zimmer HRC-01 Series, Installation And Operating Instructions Manual

Search results

Summary of Contents for HRC-01 Series

Reviews:

Related manuals for HRC-01 Series

Brands by name

Popular brands