Zimmer GEH6000IL Series Installation And Operating Instructions Manual Download | Manualshive

Page: 46 / 67

background image

46

11.9.3.3

Pre-positioning force profiles

Gripping in the direction of WorkPosition

For Mode Groups 80 and 90, pre-positioning is

used. Therefore, these groups are particularly

suitable for time-optimized gripping with long

strokes followed by force-fit gripping.

BasePosition

Speed [%]

DriveVelocity

WorkPosition

Position [mm]

PositionTolerance (PT)

PT

PT

PT

PT

PT

TeachPosition

ShiftPosition

GripVelocity

(calculated)

The gripping force is built up by the movement

speed of the product and the motor current.

The product calculates the required GripVe-

locity automatically from the GripForce

parameter.
For opening, the product moves toward the

standby position at DriveVelocity. The product

switches into positioning mode automatically.

The graphic shows outside gripping using

mode group 80 as an example. For Mode

Group 90, the BasePosition and the WorkPo-

sition are exchanged.

Opening

WorkPosition

Speed [%]

DriveVelocity

BasePosition

Position [mm]

PositionTolerance (PT)

PT

PT

PT

Parameter

Description

BasePosition

Open position

ShiftPosition

Switching from positioning to gripping

WorkPosition

Closed position

GripForce

Desired gripping force

TeachPosition

Expected position of the workpiece

PositionTolerance

Permitted tolerance for the workpiece

DriveVelocity

Opening speed

Since gripping should occur in one direction only, the positioning mode is used automatically in the opposite direction.
The movement profile determines the direction in which the workpiece is gripped:
• Outside gripping: Movement profile group 80
• Inside gripping: Movement profile group 90

INSTALLATION AND OPERATING INSTRUCTIONS:

GEH6000IL/GED6000IL

DDOC00212 / p

EN / 2022-05-01

Zimmer GmbH • Im Salmenkopf 5 •



77866 Rheinau, Germany •



+49 7844 9138 0 • www.zimmer-group.com

«
...
44
45
46
47
48
...
»

Summary of Contents for GEH6000IL Series




































































Reviews:

No comments

Related manuals for GEH6000IL Series

Brand: Raymarine Pages: 70

Brand: Keithley Pages: 67

Brand: Keithley Pages: 23

Brand: Keithley Pages: 93

Brand: Oki Pages: 44

Brand: Magnescale Pages: 64

Brand: ADVANCED HOME CARE Pages: 16

Brand: NEILPRYDE Pages: 53

Brand: JAC Pages: 103

Brand: 3Disc Pages: 12

Brand: R.M. Young Pages: 10

Brand: Water Witch Pages: 2

Brand: Falltech Pages: 48

Brand: jcb Pages: 41

Brand: lancer Pages: 3

Brand: lancer Pages: 12

Brand: R2 Pages: 26

Brand: MAGIC FX Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands