Zigmund & Shtain BTO640T, User Instructions

Page: 6 / 20

6
3PCLIOBTO.5
VITROCERAMIC HOB
User instructions
GENERAL
Carefully read the contents of this leaflet since
it provides important instructions regarding
safety of installation, use and maintenance.
Keep the leaflet for possible future consultation.
All the operations relating to installation
(electrical connections) must be carried out
by specialised personnel in accordance with
current regulations.
SAFETY WARNINGS
It is recommended to use flat-bottom pans with
a diameter equal to or slightly larger than that
of the heated area (Fig.6). �o not use pans with Fig.6). �o not use pans with . �o not use pans with
a rough base in order to prevent scratching the
heat surface of the cooking hob.
This appliance is not suitable for use by children
or persons requiring supervision.
IMPORTANT
- Avoid spilling liquid, therefore to boil or heat
liquids, reduce the heat.
- Please ensure when the appliance is turned
on, that there are no empty pots left on top.
- When you have finished cooking, switch
off the relevant heating element with the
command indicated hereinafter.
h
WARNING
h
If the surface of the hob is cracked, turn
off the appliance and disconnect from the
electrical main in order to avoid any possible
electric shocks..
INSTALLATION INSTRUCTIONS
These instructions are for a specialized installer
and are a guide for the installation process,
regulations and maintenance in accordance
with the law and current standards. If the built-
in oven or any other appliances that produce
heat, need to be installed directly underneath
the cooking hobs in ceramic glass, IT IS
NECESSARY THAT THE APPLIANCE (oven)
AND THE COOKING HOBS IN CERAMIC
GLASS ARE ADEQUATELY ISOLATED .
Failure to follow this precaution, could cause a
malfunction in the TOUCH CONTROL system.
POSITIONING
The domestic appliance was built in order to
be encased on a work surface, the way it is
illustrated in the graph (Fig.1). Predispose
sealing material along the whole perimeter Fig.
4 (the dimensions of the cut Fig.).
This operation is necessary to avoid any liquids
penetrating the worktop, as it is not possible
to guarantee that the top, the glass and their
connection are completely flat.
Lock the domestic appliance into place with 4
supporters, keeping in mind the width of the
surface (Fig.).
If the lower part of the appliance after installation,
is accessable via the lower part of the furniture,
it is necessary to mount a separating panel
keeping in mind the distances indicated (Fig.)
if the appliance is being installed underneath an
oven, this is not necessary.
ELECTRICAL CONNECTIONS (Fig.5) (Fig.5)
Before making the electrical connections, check
that:
- the ground wire is cm longer than the other
cables;
- the system ratings meet the ratings indicated
on the identification plate fixed on the lower
part of the worktop;
- the system is fitted with efficient ground wires
in accordance with the laws and current
standards.
Grounding is mandatory by law.
If the domestic appliance is not supplied with
a cable and/or suitable plug, use material
suitable for the absorption value indicated
on the identification plate and the operating
temperature. If wishing to make a direct
connection to the mains, an omnipolar switch
must be installed with a minimum mm opening
between the contacts and appropriate for the
load indicated on the plate and in accordance
with current standards (the yellow/green
ground conductor must not be disconnected
by a switch). When the appliance has been
installed, the omnipolar switch must be easily
reachable.
USE AND MAINTENANCE
MAINTENANCE
Remove any residues of food and drops of
grease from the cooking surface by using the
special scraper supplied on request (Fig.7)
Clean the heated area as thoroughly as possible
using suitable products, and a cloth/paper, then
rinse with water and dry with a clean cloth.
Using the special scraper (optional) immediately
remove any fragments of aluminium and plastic
material that have unintentionally melted on the
heated cooking area, or residues of sugar or
food with a high sugar content (Fig.7). In this
way, any damage to the cooktop surface can
be prevented. Under no circumstances should
abrasive sponges, or corrosive chemical
detergents, such as oven sprays or stain
removers, be used.
USE
Use the touch control system in the
corresponding position according to individual
cooking needs. Keep in mind that the higher the
number, the more heat is produced.
EN