Zetor Proxima HS 100 Operator'S Manual Download | Manualshive

Page: 28 / 212

background image

Tractor user must be properly acquainted with recommended operating and safety rules for

safe tractor operation in advance. It is too late to do it within operation!

Safety cab

Opening doors from the outside

Opening the door from the inside

Use the left side of the tractor for getting in and

off the cab.

Use climbing spurs for getting on and off the cab and

hold onto a handle.

Take greater care in the area of gears lever and

manual fuel control lever.

G101

Left cabin door is lockable from the outside. Right door of
the cabin are equipped only with a button from the
outside. After unlocking and pressing the button of the
lock the door opens by pulling the handle.

C120

1. Lever for opening the door from the inside
2. Lever for opening the door from the inside
The door is held by a gas strut with a full opening.
Driving with open door is not recommended for their
possible damage.

It is forbidden driving with open door due to its

possible damage.

F23

ACQUAINTANCE WITH TRACTOR

27

«
...
26
27
28
29
30
...
»

Summary of Contents for Proxima HS 100





















































































































































































































Reviews:

No comments

Related manuals for Proxima HS 100

Brand: Gearmore Pages: 14

Techstar CVT MT525B Series

Brand: Challenger Pages: 248

Brand: CAMSO Pages: 20

Brand: Winton Pages: 20

HORTUS HS Series

Brand: Zetor Pages: 142

TeeJet Matrix 908

Brand: Spraying Systems Pages: 40

Brand: Krushr Pages: 34

Brand: GGP Pages: 19

Brand: Skid Steer Pages: 12

PowerSafe 710 PS

Brand: BCS Pages: 71

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands