manualshive.com logo in svg

Zetor Proxima HS 100, Operator'S Manual

The Zetor Proxima HS 100 Operator's Manual is essential for mastering the features and maintenance of your machine. This comprehensive manual provides detailed instructions and expert guidance, ensuring smooth operation and prolonging the lifespan of your equipment. Download your free copy at manualshive.com and unleash the full potential of your Zetor Proxima HS 100.

Share
Download
background image

 

Diesel particle filter 

 The exhaust system of a tractor is equipped with a diesel particle filter which serves for cleaning 

exhaust fumes. Solid particles (carbon particles) are collected and burned in diesel particle filter which 
originate by burning diesel. 
 
Filter of solid particles - indication of operation and failures of the system 

P15N057

 

 

 Operation of the filter of solid particles is indicated by the pair of signal lamps (1) and (2) on the 

instrument panel.  
Activation of the signal lamp (1) of the green colour on the instrument panel while the engine is running 
indicates that there are optimum conditions for filter regeneration. Flashing of the signal lamp indicates that 
regeneration of the diesel particulate filter is being performed.  
Activation of the signal lamp (2) of the yellow colour on the instrument panel while the engine is running 
indicates that there is a less serious defect in the filter of solid particles (DPF). The activation of the signal 
lamp is accompanied by switching of the corresponding failure signal lamp, acoustic signal and error 
message in the instrument panel display.  
Activation of the signal lamp (2) of the red colour on the instrument panel while the engine is running 
indicates that there is a serious defect in the filter of solid particles (DPF). The activation of the signal lamp is 
accompanied by switching of the corresponding failure signal lamp, acoustic signal and error message in the 
instrument panel display. 
 
More information in chapters Instrument Panel and System of Additional Treatment of Exhaust Gases.

OPERATION

83

Summary of Contents for Proxima HS 100





















































































































































































































Reviews:

No comments

Related manuals for Proxima HS 100

Mahindra 2810 Service Manual preview
2810
Brand: Mahindra Pages: 223
Zetor MAJOR HS Series Operator'S Manual preview
MAJOR HS Series
Brand: Zetor Pages: 140
Gaggenau AW 280790 Operating And Installation Instruction preview
AW 280790
Brand: Gaggenau Pages: 24
R2 RINALDI MT Instruction And Maintenance Manual preview
MT
Brand: R2 RINALDI Pages: 32
New Holland T8010 Specifications preview
T8010
Brand: New Holland Pages: 2
Raven AutoBoom RoGator 54 Series Installation Manual preview
AutoBoom RoGator 54 Series
Brand: Raven Pages: 74
Rev-A-Shelf 5149 Series Installation Template preview
5149 Series
Brand: Rev-A-Shelf Pages: 2
Yanmar SC 2400 Operator'S Manual preview
SC 2400
Brand: Yanmar Pages: 133
Toro Wheel Horse 270HE Operator'S Manual preview
Wheel Horse 270HE
Brand: Toro Pages: 44
Toro 73429 Operator'S Manual preview
73429
Brand: Toro Pages: 44
Stara Reboke 6000 TSI Instruction Manual preview
Reboke 6000 TSI
Brand: Stara Pages: 69
MRF 14592 Operator'S Manual preview
14592
Brand: MRF Pages: 20
Komatsu D155AX-6 Brochure preview
D155AX-6
Brand: Komatsu Pages: 6
Komatsu D275A-5R Brochure preview
D275A-5R
Brand: Komatsu Pages: 8
Komatsu D155AX-8E0 Operation & Maintenance Manual preview
D155AX-8E0
Brand: Komatsu Pages: 420

Brands by name

Popular brands

Load more brands