manualshive.com logo in svg

Zetor Proxima HS 100, Operator'S Manual

The Zetor Proxima HS 100 Operator's Manual is essential for mastering the features and maintenance of your machine. This comprehensive manual provides detailed instructions and expert guidance, ensuring smooth operation and prolonging the lifespan of your equipment. Download your free copy at manualshive.com and unleash the full potential of your Zetor Proxima HS 100.

Share
Download
background image

 

Two-hose brakes 

Hydraulic brakes of trailers 

 
Connecting and disconnecting quick couplings of trailer hydraulic brakes 

 

When connecting and disconnecting quick couplings, take increased care with regard for 

remaining oil which remains in the socket or in the plug of quick coupling. For ecological reasons, it 
is necessary to remove this remaining oil after every disconnection of quick couplings with any 

textile material. 

    

 

Stopping the tractor - hand brake 

Operating pressure is adjusted with the control valve at 
740 ± 20 kPa. Capacity of air tank is 20 l.  
The valve of the left head is labelled in yellow (braking 
branch), the valve of the right head is labelled in red (filling 
branch).  

 

When connecting the trailer (articulated trailer) 

with a maximum permitted speed approved for the 

type of tractor, the maximum permitted speed of set is 

40 km per hour! 
Maximum permitted speed of set is given by maximum 

permitted speed of the slower vehicle of the set. 

 

P11NX229

 

 

Connect hydraulic brakes of trailer or articulated 

trailer to the quick couplings marked by an arrow. 

Control of hydraulic brakes of trailers (articulated trailers) 
and control of tractor brakes is done so that the braking 
effect of both vehicles is synchronized. Working pressure 
is derived by oil supplied by non-switched on/switched off 
gear pump of hydraulics. Brake valve of the trailer is done 
by the pressure of brake fluid from main braking rollers 
depending on the force effecting on the brake pedal. The 
pressure on clutch head must be 12 - 15 MPa with 
maximum depression of brake pedal. Brake valve of trailer 
prefers the function of brakes to the function of hydraulics. 
If there are shocks when foot brake pedals are depressed 
in the pipeline of hydraulic circuit, it is necessary to bleed 
the hose from the brake valve to the quick coupling. 

 

When driving with connected trailer or 

articulated trailer, the pedals of foot brake must be 

connected and secured by a valve! When braking with 

one brake pedal, hydraulic brakes of the trailer are not 

active.

 

P11NE231

 

 

Under normal conditions stop the tractor slowly. Shortly 
before stopping: 

1. Tread on the clutch pedal and brake the tractor by the 
foot brake. 
2. Move the main shifting lever to neutral position. 
3. With each stop secure the tractor using the hand brake 
against spontaneous moving off. Application of the hand 
brake is indicated by a light on the dashboard. 

G232

 

 

OPERATION

96

Summary of Contents for Proxima HS 100





















































































































































































































Reviews:

No comments

Related manuals for Proxima HS 100

Zetor Proxima 70 2012 Operator'S Manual preview
Proxima 70 2012
Brand: Zetor Pages: 214
Cucine Oggi Wesco Ergo-Master 060100-47 Assembly Instructions preview
Wesco Ergo-Master 060100-47
Brand: Cucine Oggi Pages: 3
WBT SUMO UNI LIFT User And Safety Manual preview
SUMO UNI LIFT
Brand: WBT Pages: 28
Textron Steiner 420 Owner'S/Operator'S Manual preview
Steiner 420
Brand: Textron Pages: 26
Daedong KIOTI CS2610 Manual preview
KIOTI CS2610
Brand: Daedong Pages: 192
Farmtrac 6060DT Operator'S Manual preview
6060DT
Brand: Farmtrac Pages: 54
Komatsu D31EX-22 Brochure preview
D31EX-22
Brand: Komatsu Pages: 8
Zetor Proxima 100 2012 Operator'S Manual preview
Proxima 100 2012
Brand: Zetor Pages: 214
Tiger JD5075E T4F Mounting And Operating Instructions preview
JD5075E T4F
Brand: Tiger Pages: 202
Tiger BENGAL JD6110-20M/R MY20 Mounting And Operating Instructions preview
BENGAL JD6110-20M/R MY20
Brand: Tiger Pages: 223
Tiger BENGAL JD6110-30M/R T4F Mounting And Operating Instructions preview
BENGAL JD6110-30M/R T4F
Brand: Tiger Pages: 226
Tiger WILDKAT JD6105-25E T4F Manual preview
WILDKAT JD6105-25E T4F
Brand: Tiger Pages: 240
Tiger JD6175R Mounting And Operating Instructions preview
JD6175R
Brand: Tiger Pages: 236
Tiger BENGAL JD51 M Series Mounting And Operating Instructions preview
BENGAL JD51 M Series
Brand: Tiger Pages: 240
Tiger WILDCAT JD6105D Mounting And Operating Instructions preview
WILDCAT JD6105D
Brand: Tiger Pages: 252
Tiger WILDKAT JD61 M/R Series Manual preview
WILDKAT JD61 M/R Series
Brand: Tiger Pages: 258
Tiger BENGAL 5085M Series Mounting And Operating Instructions preview
BENGAL 5085M Series
Brand: Tiger Pages: 294
NPK Genesis GSD 10 Safety & Operators & Parts Manual preview
Genesis GSD 10
Brand: NPK Pages: 29

Brands by name

Popular brands

Load more brands