manualshive.com logo in svg

Zetor Proxima HS 100, Operator'S Manual

The Zetor Proxima HS 100 Operator's Manual is essential for mastering the features and maintenance of your machine. This comprehensive manual provides detailed instructions and expert guidance, ensuring smooth operation and prolonging the lifespan of your equipment. Download your free copy at manualshive.com and unleash the full potential of your Zetor Proxima HS 100.

Share
Download
background image

 

Replacement of the transmission oil cleaner element with hydraulic pump suction filter  

Gearbox distributor - replacement of oil cleaner cartridge 

G749

 

 

The gearbox distributor is located on the right side of the tractor behind the fuel tank; the oil cleaner is 
accessible from the bottom of the tractor.  

 Before replacement of the oil cleaner cartridge, put a suitable container under the tractor to 

catch any leaking oil.  

1. Screw out the cleaner body (1).  
2. Replace the filtration cartridge (2).  
3. Reinstall the cleaner body (1). 

Front PTO  

The oil cleaner is placed on the left side of the gearbox.  

 

Before replacing the oil cleaner element, place 

a suitable vessel for dripping oil under the tractor.  

1. Unscrew the body of the cleaner (1)  
2. Replace the filtration element  
3. Reassemble the body of the cleaner  

P11N005

 

 

The inspection and filling plug of oil (1) is situated on the 
front side of the front PTO case.  
 

Note:

 The front PTO with the standard turning direction is 

equipped with a hollow bolt of the oil cooler hose instead 
of the inspection and filling plug. Perform the check after 
removing the hollow bolt.  

 

After unscrewing of the inspection plug the oil 

level must reach the bottom edge of the inspection 

opening. During the oil replacement the oil cleaning 

strainer (2) must be cleaned. The cleaning strainer is 

accessible after the disassembly of the locking ring 

and removal of the cap.  

 

F206

 

 

MAINTENANCE INSTRUCTIONS

179

Summary of Contents for Proxima HS 100





















































































































































































































Reviews:

No comments

Related manuals for Proxima HS 100

FENDT 512 Vario S4 Workshop Service Manual preview
512 Vario S4
Brand: FENDT Pages: 6
New Holland TN75FA Service Manual preview
TN75FA
Brand: New Holland Pages: 14
New Holland T8010 Service Manual preview
T8010
Brand: New Holland Pages: 81
Degelman Speedblade 15 Manual preview
Speedblade 15
Brand: Degelman Pages: 27
Agrison 100HP CDF Operation Manual preview
100HP CDF
Brand: Agrison Pages: 204
DINGO K9-2 Operation & Maintenance Manual preview
K9-2
Brand: DINGO Pages: 20
FENDT 938 Vario MT Workshop Service Manual preview
938 Vario MT
Brand: FENDT Pages: 51
M-B MSV Maintenance And Service Manual preview
MSV
Brand: M-B Pages: 427
LAMBORGHINI CHAMPION 120 Workshop Manual preview
CHAMPION 120
Brand: LAMBORGHINI Pages: 41
Taylor-Dunn TT-416 Operator'S Manual preview
TT-416
Brand: Taylor-Dunn Pages: 56
Husqvarna HELT151B Spare Parts preview
HELT151B
Brand: Husqvarna Pages: 18
Husqvarna 960 41 00-52 Illustrated Parts List preview
960 41 00-52
Brand: Husqvarna Pages: 18
Husqvarna 96043014300 Repair Parts Manual preview
96043014300
Brand: Husqvarna Pages: 19
Toro 23172 Installation Instructions preview
23172
Brand: Toro Pages: 4
Toro 78269 Operator'S Manual preview
78269
Brand: Toro Pages: 20
Soucy S-TECH 7016 Installation, Operation And Maintenance Manual preview
S-TECH 7016
Brand: Soucy Pages: 84
Soucy PUMA 115 User Manual preview
PUMA 115
Brand: Soucy Pages: 154
MULTIQUIP Mikasa MVH-702DRSC Operation And Parts Manual preview
Mikasa MVH-702DRSC
Brand: MULTIQUIP Pages: 58

Brands by name

Popular brands

Load more brands