manualshive.com logo in svg

Zero Motorcycles DS 2021, Owner'S Manual

Share
Download
Zero Motorcycles DS 2021 Owner'S Manual Download Page 94

General Maintenance

6.22

Headlight Bulb Replacement

WARNING!

 Halogen bulbs contain gas under pressure. Handling 

a bulb improperly could cause it to shatter into flying glass 
fragments, which could result in serious injury. To help avoid 
injury:

•

Turn the key switch OFF and allow the bulb to  cool before 
changing the bulb.

•

Leave the key switch OFF until the bulb change is  complete.

•

Always wear eye protection when changing a  halogen bulb.

•

Avoid touching the glass.

CAUTION: 

Using higher wattage bulbs that specified can/will 

cause the headlight lens to melt.

To replace the bulb:

1. Working from behind the headlight, disconnect the headlight 

bulb connector (A) and rubber cover (B).

Zero Owner's Manual (S and DS).book  Page 22  Monday, September 21, 2020  11:43 AM

Summary of Contents for DS 2021

































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands