manualshive.com logo in svg

Zero Motorcycles DS 2021, Owner'S Manual

Share
Download
Zero Motorcycles DS 2021 Owner'S Manual Download Page 114

Troubleshooting

7.10

Hot Weather Operation

Operation of the motorcycle in hot temperatures should not 
result in any noticeable performance changes. However, the 
BMS will not allow motorcycle operation and its associated 
power pack discharge above 140°F (60°C), as measured at the 
power pack.

In hot temperatures greater than 109°F (43°C), the charger 
reduces its charge current to the power pack, increasing charge 
time accordingly; the hotter the ambient temperature, the 
greater the effect. Above a power pack temperature of 122°F 
(50°C), the BMS will no longer allow charging. 

Note: Storing the motorcycle or its battery in direct sunlight in 
ambient temperatures above 95°F (35°C) may result in 
accelerated permanent decay of power pack performance, and 
hence it is not recommended.

Zero Owner's Manual (S and DS).book  Page 10  Monday, September 21, 2020  11:43 AM

Summary of Contents for DS 2021

































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands