manualshive.com logo in svg

Zero Motorcycles DS 2021, Owner'S Manual

Share
Download
Zero Motorcycles DS 2021 Owner'S Manual Download Page 61

General Operation

4.17

Compression Adjustment

The compression  adjustment knob is at the top of the shock. 
Printed on the knob is “H” meaning 

Hard

 (

MAX

, which is for 

slower compression) and “S” meaning 

Soft

 (

MIN

, which is for 

faster  compression). Turn the adjuster clockwise for a harder 
ride (slower compression). For a softer ride (faster 
compression), turn the adjuster counter-clockwise. Start with a  
middle setting and fine tune the compression  from there. Proper 
compression allows the tire to track the ground over consecutive 
bumps. Compression that is set too hard will pack-up (feel harsh 
over consecutive bumps), while compression that is set too soft 
causes the shock to bottom out harshly. If the shock is  
bottoming out, turn the adjuster one click at a  time until the 
bottom out stops.

Note: Adjusters should never be forced completely “Soft” or 
“Hard”; always leave one click of adjustment  in either direction.

Zero Owner's Manual (S and DS).book  Page 17  Monday, September 21, 2020  11:43 AM

Summary of Contents for DS 2021

































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands