manualshive.com logo in svg

Zero Motorcycles DS 2021, Owner'S Manual

Share
Download
Zero Motorcycles DS 2021 Owner'S Manual Download Page 92

General Maintenance

6.20

7. Rotate the rear wheel a quarter-turn and repeat the frequency 

measurement.

8. Compare your belt’s frequency readings to the 

recommended range values below.

9. Adjust drive belt tension if the frequency is outside the 

recommended range.

Drive Belt Adjustment Procedure

Note: Adjust both sides (left and right) equally.

1. Remove key from the key switch.

2. Loosen the rear axle nut (A). 

3. Loosen the (left and right) 13 mm jam nuts (C). 

4. Turn the (left and right) 13 mm adjustment bolts (B) 1/4 turn 

at a time until the belt adjustment is within specification.

5. Tighten left and right jam nuts (C) to secure the belt.

6. Tighten the axle nut (A). 

7. Test ride the motorcycle. 

8. Recheck the belt for proper adjustment after the test ride and 

readjust, if necessary.

Belt Pitch

Recommended Tension Range

11 mm

42.5 Hz to 73.6 Hz

Zero Owner's Manual (S and DS).book  Page 20  Monday, September 21, 2020  11:43 AM

Summary of Contents for DS 2021

































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands