manualshive.com logo in svg

Zero Motorcycles DS 2021, Owner'S Manual

Share
Download
Zero Motorcycles DS 2021 Owner'S Manual Download Page 56

General Operation

4.12

Compression Damping

The compression  damping is adjusted by turning a screw on the 
bottom of each fork leg. Next to the screw are the letters “H” 
meaning 

Hard

 (

MAX

, which is for slower compression) and “S” 

meaning 

Soft

 (

MIN

, which is for faster compression). 

•

Turn the adjuster screw (A) clockwise  for slower 
compression. 

•

To speed up  compression, turn the adjuster screw 
counter-clockwise.

Start with a middle setting and fine tune the compression from 
there. Proper compression  allows the tire to track the ground 
over consecutive bumps. Compression that is set too slow will  
pack-up (feel harsh over consecutive bumps),  while 
compression that is set too fast will cause the fork to bottom out 

harshly. If the fork is  bottoming out, turn the adjuster one click 
at a  time until the bottom-out stops. Adjust each fork  leg evenly.

Note: Adjusters should never be forced completely  “Soft” or 
“Hard”; always leave one click of adjustment  in either direction.

Zero Owner's Manual (S and DS).book  Page 12  Monday, September 21, 2020  11:43 AM

Summary of Contents for DS 2021

































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands