Zepro ZS 150-135 Installation Instruction Download Page 6

Page: 6 / 62

Some components of the tail lift must be manipulated by ceiling cranes and therefore could represent ha-

zards if their weights exceed the crane's permitted load. The following are the ranges of weights for various

heavy components.

2. General

Weights

ZS = Single folded platform, for truck installation,

hydraulic motor placed above support frame.

ZSS = Single folded platform, for truck installation,

hydraulic motor placerad in front of support frame.

ZD = Double folded platform, for truck installation,

hydraulic motor placed above support frame.

ZT = Single folded platform, for trailer installation,

hydraulic motor placed above support frame.

ZTS = Single folded platform, for trailer installation,

hydraulic motor placerad in front of support frame.

Max liftcapacity x 10 (kg)
Max lifting height --135 = 1350 mm, -140 = 1450 mm

-155 = 1540 mm, -175 = 1725 mm

Cylindermodel, ML = Double acting Tilt, limited stroke

Single acting one speed Lift

DL = Double acting Tilt, limited stroke

Double acting one speed Lift

E.g. ZS - 150 - 135 ML

_ _ - _ _ _ - _ _ _ _ _

Identification list, slider lifts

Lift components (part of cpl. lift chassis).

Support frameZS/ZSS/ZD 150/200/250 84 kg

Support frame ZT-ZTS 150/200/250

76 kg

Lift arm ZS/ZSS/ZD 150/200-135

46 kg

Lift arm ZS/ZSS/ZD 250-135

50 kg

Lift arm ZS/ZSS/ZD 150/200-155

50 kg

Lift arm ZS/ZSS/ZD 250-155

54 kg

Lift arm ZS/ZSS/ZD 150/200-175

54 kg

Lift arm ZT-ZTS 150/200/250-140

51 kg

Lift cylinder ZT/ZTS 150-140

13,1 kg/pce.

Lift cylinder ZT/ZTS 200/250-140

14,3 kg/pce.

Lift cylinder ZS/ZSS/ZD 150/200-135

8,5 kg/pce.

Lift cylinder ZS/ZSS/ZD 150/200-155

9,5 kg/pce.

Lift cylinder ZS/ZSS/ZD 150/200-175

10,5 kg/pce.

Tilt cylinder ZT/ZTS 150/200/250-140 14,5 kg/pce.

Tilt cylinder ZS/ZSS/ZD 150/200-135

13 kg/pce.

Tilt cylinder ZS/ZSS/ZD 150/200-155

14,5 kg/pce.

Tilt cylinder ZS/ZSS/ZD 150/200-175

16 kg/pce.

Lift cylinder ZS/ZSS/ZD 250-135

11 kg/pce.

Lift cylinder ZS/ZSS/ZD 250-155

12,3 kg/pce.

Tilt cylinder ZS/ZSS/ZD 250-135

13,5 kg/pce.

Tilt cylinder ZS/ZSS/ZD 250-155

15 kg/pce.

Rollarm cpl. (only ZD)

12 kg

Hydraulic auto-tilt

10 kg

Cpl. Lift chassis (without platform)

(1590 mm slide profiles)

ZS/ZSS-150/200-135 => 401 kg

ZS/ZSS-250-135 => 412 kg

ZS/ZSS-150/200-155 => 410 kg

ZS/ZSS-250-155 => 421 kg

ZS/ZSS-150/200-175 => 419 kg

1370 mm slide profiles instead of 1590 mm -10 kg

1550 mm slide profiles instead of 1590 mm -2 kg

(1095 mm slide profiles)

ZD-200-155 => 393 kg

ZD-200-175 => 402 kg

1215 mm slide profiles instead of 1095 mm

+4 kg

(1700 mm slide profiles)

ZT/ZTS 150-140 => 415 kg

ZT/ZTS 200/250-140 => 418 kg

Summary of Contents for ZS 150-135































































Search results

Summary of Contents for ZS 150-135

Reviews:

Brands by name

Popular brands

Zepro ZS 150-135, Installation Instruction

Search results

Summary of Contents for ZS 150-135

Reviews:

Brands by name

Popular brands