47
II. Liquidizer
a) cup/dispenser,
b) lid,
c) gasket,
d) liquidizer container.
How to use the accessories
Food processor blade
– is used to process meat, mix
dough and other functions.
Slicing disc
– is used to cut fruits and vegeta-bles into thin
and thick slices.
Shredding disc
– is used to shred fruits and vegetables into
fine or coarse shreds.
French fry slicing disc
– is used to cut pota-toes for French
fries.
Pureeing disc
– is used to pulp fruits and vegeta-bles.
Disc driver
– is used to install changeable discs.
Food pusher, dispenser
– is used to push ingredients that
are grinded by the slicing discs, to dispense loose or liquid
ingredients and to close the feed tube of the lid. A small
opening at the bottom of the food pusher allows to evenly
dispense liquids (e.g. oil while preparing may-onnaise).
Liquidizer
– is used to prepare food of liquid or semi-liquid
consistency such as: soups, creams, sauces, cocktails and
others.
Slicing
and shredding discs are round, with two-sided blades
(one side for thin slices, the other for thick slices).
Preparation for operation, start-up and
operation
Wash the parts that have contact with the processed
●
food before initial use.
Place the motor on a hard, clean and dry surface near
●
the electrical outlet.
Unwind a sufficient length of the cord. The remaining
●
cord can be stored in the housing. Put the remaining
cord in the housing through the opening at the back of
the housing.
Choose the appropriate attachments depend-ing on the
●
selected type of operation.
Operating the food processor
Place the food processor container on the fastening hooks
of the motor so that the sign
on the container is
opposite the sign
on the housing and turn the container
counterclockwise until the fastening hooks snap shut
(position
).
Operating the food processor blade (fig. 2a)
Put the blade in the casing on a hard surface (put in on
●
the casing).
Press the blade and remove the casing by pulling it
●
upwards.
Place the blade in the container so that it is connected to
●
the motor shaft.
Put the ingredients to be processed inside the container
●
according to the selected recipe.
Put the lid on the fastening hooks of the con-tainer so
●
that the sign
on the lid is opposite the sign
on the container and turn the lid anticlockwise until the
hooks snap shut (position
).
Put the food pusher into the feed tube of the lid.
●
Plug in the appliance.
●
Set the desired speed using the knob and switch on the
●
appliance - set the switch in the position “
1
”.
The food processor may also be switched on by
setting the switch in the “pulse” posi-tion.
Operating the slicing disc
(Fig. 2b)
Put the selected slicing disc on the hooks of the disc
●
driver so that the blades that are to be used during
operation are on top and turn the disc driver anticlockwise
until stop.
Place the tool in the container so that it is connected to
●
the motor shaft.
Put the lid on the fastening hooks of the container so that
●
the sign
on the lid is opposite the sign
on the
container and turn the lid anticlockwise until the hooks
snap shut (position
).
Plug in the appliance. Set the desired speed using the
●
knob and switch on the appliance - set the switch in the
position “
1
”.
The food processor may also be switched
on by sliding the switch to the “pulse” position.
The feed tube of the lid is used to add solid and liquid
ingredients to the container. It is divided into two parts
of different sizes. The wide part is for larger products and
the narrow part is for smaller products. Add the processed
products gradually, pushing them slowly and with a steady
thrust down the feed tube with the pusher.
Operating the liquidizer
(Fig. 2c)
Put the liquidizer container on the fastening hooks of the
–
motor so that the sign
on the container is opposite
the sign
on the housing and turn the container
anticlockwise until the hooks snap shut (position
).
Put the ingredients to be processed inside the container
–
according to the selected recipe.
Make sure the gasket is properly installed in the groove
–
by the edge of the lid.
The rectangular protrusion of the gasket is used to
–
remove the gasket from the lid.
Put the lid of the liquidizer on the fastening hooks of the
–
container so that the sign
on the lid is opposite the
sign
on the container and turn the lid anticlockwise
until the hooks snap shut (position
).
Press the cup-dispenser into the opening of the lid.
–
Plug in the appliance.
–
Set the desired speed using the knob and switch on the
–
Summary of Contents for 882.3
