Z3 Technology Z3-MVE-02 User Instructions Download Page 32

Page: 32 / 36

DOC-USR-0038-05

_______________________________________________________________________________________

Z3 Technology, LLC

♦

100 N. 8th St. STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

Stop Encoder
[Button]

-----

Stop current encode session.

Start Encoder
[Button]

-----

Start encode session.

Status

Idle

, Stopped, Running

Current status of the encoder.

Load Factory Default
Settings [Button]

-----

Load the default values installed at the
factory.

Load User Settings
[Button]

-----

Load settings previously saved by the user.

Save User Settings
[Button]

-----

Save current settings to a file.

set name

-----

Set name for the Z3-MVE-02.

set pass

-----

Assign a password to the Z3-MVE-02 (if
logging in, the user name corresponding to
this is “admin”).

UPDATE [Button]

-----

Update firmware.

Note 1: Input resolutions Supported:

1080i (1920x1080), 3/4 1080i (1440x1080), XGA (1280x1024), 720p (1280x720), 4/5 720p (1024x720),
D1 NTSC (720x480), D1 PAL (720x576), 4-CIF (704x576), VGA (640x480) 2-CIF (352x576), CIF
(352x288), SIF (352x240), QVGA (320x240), WQVGA (320x180)

Summary of Contents for Z3-MVE-02





































Search results

Summary of Contents for Z3-MVE-02

Reviews:

Related manuals for Z3-MVE-02

Brands by name

Popular brands

Z3 Technology Z3-MVE-02, User Instructions

Search results

Summary of Contents for Z3-MVE-02

Reviews:

Related manuals for Z3-MVE-02

Brands by name

Popular brands