YZ Systems DynaPak 3010RNM Series Support Manual Download Page 3

3

DynaPak 3010RNM Version 01102001 ATEX Rev.

YZ Systems, Inc. • 3101 Pollok Drive • Conroe, Texas • USA • 77303 • P: 936.788.5593 • F: 936.788.5720

Table of Contents

1. Introduction

4

2. System Components

4

3. Theory of Operation

5

4. System Installation

•with slipstream kit

6

•with pulse input

7

5. Sample Vessel Installation

8

6. Operational Checks & Leak Testing

9

7. Sampler  Set-Up:  Continuous
     time-based sampling

10

8. Sampler Set-Up:  Continuous
     proportional-to-flow sampling

12

9. Sampler Maintenance

16

10. Troubleshooting

20

11. Diagrams
  #1

DP-3000 HP pump (assembled)

23

  #2

DP-3000 HP pump (exploded)

24

    #3

YZ external actuation filter/regulator
(assembled)

25

    #4

YZ external actuation filter/regulator
(exploded)

26

  #5

Z-65/6.1 controller

27

  #6

LinkPlus

28

    #7

Z-65 installation notes/wiring documents 29

  #8

DuraSite sample vessel instructions

30

  #9         About the PIM-100...

32

YZ Systems, Inc. represents and warrants that for a period of 3 years from receipt of the product: (1) the product will be free from defects in materials and

workmanship; and (2) the product will perform substantially in accordance with product manuals, literature, or documentation.  Any written or oral information or advice
given by YZ representatives, agents, or employees will in no way increase the scope of this warranty.  If the product fails to comply with the warranty set forth herein, YZ's
entire liability and the customer's exclusive remedy will be replacement of the product(s) or, at YZ's option, YZ's reasonable effort to make the product meet the warranty
set forth herein.  YZ disclaims all other warranties, either expressed or implied, including but not limited to, implied warranties or merchantability and fitness for a
particular purpose, with respect to the product.
  This limited warranty gives you specific legal rights.  You may have others, which vary from state to state.  These
remedies are not available outside of the United States and Canada.
  In no event shall YZ or its suppliers be liable for any damages whatsoever (including, without
limitation, damages for loss of profits, business interruption, loss of information, or other pecuniary loss) arising out of the use of or inability to use the product, even if
YZ has been advised of the possibility of such damages.  Information contained in this document is subject to change without notice and does not represent a
commitment on the part of YZ Systems, Inc.  All prices quoted are in U.S. dollars, F.O.B. Snyder, Texas.  NJEX is a  trademark of YZ Systems, Inc.  All other product names
and/or registered trademarks are the property of their respective holders.  YZ support services are subject to YZ's then-current prices, terms, and conditions, which are
subject to change without notice.  All prices and specifications, if published, are subject to change without notice.

Summary of Contents for DynaPak 3010RNM Series


































Reviews: