YSI YSI 556 MPS Set-Up, Operation & Calibration Download | Manualshive

Page: 26 / 68

background image

Dissolved Oxygen

•

NOTE:

The instrument must be on for at least

20 minutes to polarize the DO sensor before
calibrating.

•

Use the arrow keys to highlight the

Dissolved

Oxygen

selection.

•

Press

Enter

. The dissolved oxygen calibration

screen is displayed.

•

Use the arrow keys to highlight the DO%
selection.

•

Press

Enter

. The DO Barometric Pressure

Entry Screen is displayed.

•

Place approximately 3 mm (1/8 inch) of water in
the bottom of the transport/calibration cup.

•

Place the probe module into the
transport/calibration cup.

«
...
24
25
26
27
28
...
»

Summary of Contents for YSI 556 MPS





































































Reviews:

No comments

Related manuals for YSI 556 MPS

Brand: janitza Pages: 12

Brand: janitza Pages: 84

Brand: janitza Pages: 6

Brand: janitza Pages: 14

Brand: janitza Pages: 98

Brand: Sensia Pages: 16

Brand: Velleman Pages: 96

Brand: Kawai Pages: 8

Brand: Yamaha Pages: 8

Brand: Lutron Electronics Pages: 13

Brand: Xtralis Pages: 13

Brand: Tektronix Pages: 124

Brand: Rodstation Pages: 28

QI-POWER-485-300

Brand: QEED Pages: 2

Brand: Sonel Pages: 84

sound SMART RLT Sport

Brand: VCA Pages: 36

Brand: Magnescale Pages: 2

Brand: Omega Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands