Yolico YD3000N Series, Instruction Manual, Page: 72 / 139

Setting:
1 to 5
Setting: 6
Sign
The sign bit is used as a data bit, so only positive (plus) data
can be set.
The second digit below the decimal point is set by bits 8x100,
4x100, and 2x100, so the settings aremade in units of 0.02 Hz
. (If these three bits are “111,” “110,” and “101,” they will be
recognized as“9.”)
If “2” or higher is set for o1-03, the input will become BCD, and
the units will change to the o1-03 setting.
SettingRange SettingRange
Function Function
Effective when the Analog Monitor Card is used.
8
SettingRange SettingRange
Function Function
Effective when the Analog Monitor Card is used.
SettingRange SettingRange
Function Function
Effective when the Analog Monitor Card is used.
SettingRange SettingRange
Function Function
SettingRange SettingRange
Function Function
Sets the channel 1 item bias to100%/10 V when the analog
monitor
card is useditor used.
SettingRange SettingRange
Function Function
Description of choice Description of choice
Sets the channel 2 item bias to 100%/10 V when the analog monitor
card is used itor used.
When using an AO-08 or AO-12 Analog Monitor Card, set the monitor
items and gain with the followingconstants
● For the output monitor selections (F4-01, F4-03), set the numbers
for the right side of the “U1”constants in the Table 4.3. The setting
range is 1 to 38, but the follo wing numbers cannot be set: 4, 10,
11, 12, 13, 14, 25, and 28 to 35.
● When the AO-12 is used, outputs of 0 to ±10 V are possible.
For that, set constant H4-07 (multi-functionanalog output signal
level selection) to “1” (0 to ±10 V outputs). There are some monitor
items.However, that can only use outputs of 0 to +10 V even if
constant H4-07 is set to “1.”
● When the AO-08 is used, only
outputs of 0 to +10 V are possible regardless of the constant
H4-07 setting.
SettingRange SettingRange
Function Function
Effective when a Digital Output Card is used.Set the number
of the multi-functionoutput to be output.
SettingRange SettingRange
Function Function
Set the output selections in the following constants when
using a DO-02 Digital Output Card.
Description of choice Description of choice
Set the output selections in the following constants when
using a DO-02 Digital Output Card.
Channel 1
output
selection
Channel 2
output
selection
Name Name
User
Constant
Number
User
Constant
Number
Change
during
Operation
Change
during
Operation
Setting
Rang e
Setting
Rang e
Unit Unit
Factory
Setting
Factory
Setting
V/f
Control Control
V/f with V/f with
PG
OpenLoop
Vector
OpenLoop
Vector
Flux
Vector
Flux
Vector
Function Function
Description of choice Description of choice
channels of individual out outputs
Binary code output
Effective when a DO-08 DigitalOutput Card is used.Set the
output mode.
Set the output mode in the following constants when using
a DO-08 Digital Output Card.
The items output from the DO-08 will be as follows according
to the setting of F6-01.
Effective when a Digital OutputCard is used.Set the number
of the
multi-functionoutput to be output.
Is a registered trademark of yolico
Set the number of the muli - fune - tion output to be
output
YD3000N
نوﯾﺳﺎﻣوﺗا ﯽﺗﻌﻧﺻ
ﮏﯾرﺗﮑﻟاوﺑار
قرﺑ
و