Language selection for digital operator
display
(Select Language)
Constant access level
(Access Level)
Control method selection
(Control Method)
Initialize
(Init Parameters)
Password 1
(Enter Password)
P a s s w o r d 2
(Select Password)
User setting constant
(User Pram 1 to 32)
Reference selection
(Reference Source)
Operation method selection
(Run Source)
Stopping method selection
(Stopping Method)
Prohibition of reverse operation
(Reverse Oper)
Operation selection for setting of
E1-09 or less
(Zero-Speed Oper)
Read sequence input twice
(Cntl Input Scans)
Operation after switching to remote
mode:2
(LOC/REM RUN Sel)
Run command selection for PRG mode
(RUN CMD at PRG)
Zero speed level (DC injection braking
start
frequency)(DCInj Start Rreq)
DC injection braking current
(DCinj Current)
DC injection braking time at start
(DCInj Time @ Start)
DC injection braking time at stop
(DCInj Time @ Stop)
Magnetic flux compensation volume
(Field Comp@ Start)
Speed search selection at start
(SpdSrch at Start)
Speed search operating current
(SpdSrch Current)
Speed search deceleration time
(SpdSrch Dec Time)
Speed search deceleration time
(SpdSrch Dec Time)
Timer function OFF-delay time
(Delay-OFF Timer)
PID control mode selection
(PID Mode)
Proportional gain (P)
(PID Gain)
ntegral (I) time
(PID I Time)
Integral (I) limit
(PID I Limit)
Differential (D) time
(PID D Time)
P I D l i m i t
(PID Limit)
PID offset adjustment
(PID Offset)
PID primary delay time constant
(PID Delay Time)
PID output characteristics selection
(Output Level Sel)
PID output gain
(Output Gain)
PID reverse output selection
(Output Rev Sel)
Selection of PID feedback command
loss detection
(Fb los Det Sel)
PID feedback command loss detection
level
(Fb los Det Lvl)
PID feedback command loss detection
time
(Fb los Det Time)
Dwell frequency at start
(Dwell Ref @ Start)
Dwell time at start
(Dwell Time @ Start)
Dwell frequency at stop
(Dwell Ref @ Stop)
Dwell time at stop
(Dwell Time @ Stop)
Droop control gain:2
(Droop Gain)
Droop control delay time:2
(Droop Delay Time)
Energy-saving gain
(Energy Save Gain)
Energy-saving frequency
(Energy Save Freq)
Zero-servo gain
(Zero Servo Gain)
Zero-servo completion width
(Zero Servo Count)
Acceleration time 1
(Accel Time 1)
Deceleration time 1
(Decel Time 1)
Acceleration time 2
(Accel Time 2)
Deceleration time 2
(Decel Time 2)
Acceleration time 3
(Accel Time 3)
Deceleration time 3
(Decel Time 3)
Acceleration time 4
(Accel Time 4)
Deceleration time 4
(Decel Time 4)
Emergency stop time
(Fast Stop Time)
Accel/decel time setting unit
(Acc/Dec Units)
Accel/decel time switching frequency
(Acc/Dec SW Freq)
S-curve characteristic time at
acceleration start
(Scrv Acc @ Start)
S-curve characteristic time at
acceleration end(SCrv Acc @ End)
* 1. Not initialized. (Japanese standard specifications: A1-01 = 1, A1-02 = 2)
* 2. Not displayed for some models depending on software version No.
* 3. Factory setting depends on the control method (A1-02).
Name
(Display)
Name
(Display)
Factory
Setting
Factory
Setting
Setting
Setting
No.
No.
Is a registered trademark of yolico
YD3000N
نوﯾﺳﺎﻣوﺗا
ﯽﺗﻌﻧﺻ
ﮏﯾرﺗﮑﻟاوﺑار
قرﺑ
و